Bedienungsanleitung Midland BTX1 PRO 2020 (Seite 12 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

738680

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

8 www.midlandeurope.com www.midlandeurope.com 9

From the mobile keypad:

Dial the number on the mobile keypad:

Press “Send” on the mobile phone.

To redial the last number:

Phone on Vol+: Press“Forward”button for 3 seconds in order to redial the last number

(you will hear one audio conﬁrmation tone).

Phone on Vol-: Press“Backward”button for 3 seconds in order to redial the last number

(you will hear one audio conﬁrmation tone).

To make a voice call:

Phone on Vol+: Brieﬂy press“Forward”button. If your mobile phone supports voice calls,

you will be asked to speak the name of the contact you wish to call.

Phone on Vol-: Brieﬂy press“Backward”button. If your mobile phone supports voice calls,

you will be asked to speak the name of the contact you wish to call.

Priority: Calls have a high priority, which means that all other communications are tempora

rily disabled when a call arrives.

Ending a call

There are several ways to end a call:

› Wait for the called person to end the call.

› Press the “Forward” button (you will hear an audio conﬁrmation tone).

› Press “End” button on the mobile phone.

Speed dial

You can store one phone number in the unit memory and use it when needed. You must

ﬁrst save the number using the “BT UPDATER” Pc software or the smartphone “BT

SET-APP” application. Then when you are in phone mode, just press 7 sec. the “Forward”

button.

Using the MP3 player feature of the mobile phone

The mobile phone, when paired on “Volume +” can be used as stereo MP3 players. The

BTX1 PRO device fully supports the A2DP and AVRCP protocols that enable you to

listen to stereo music and remotely control your mobile phone’s MP3 player. You can

even use the buttons on the BTX1 PRO unit to control the following play options: Play,

Pause, Forward and Backward of the songs.

Play/PauseForward Backward

Available controls:

› To play/pause music: click on the “Middle” button.

› To skip forward to the next song: press the “Forward” button.

› To skip backwards to the previous song: press the “Back” button.

Priority: the music listening mode has the lowest priority. Therefore, it will always be disabled

when another audio communication come in.

B-Phone mode

Mode Forward button (Phone on Vol+) Middle button Backward button (Phone on Vol-)

Phone Short press: Voice dial /accept or close if it is in

progress

Long press: redial last number/ or reject

Long press: Change mode Short press: Voice dial /accept or close if it is in

progress

Long press: redial last number/ or reject

Phone (when music is plaing

and paired on “Vol +”)

Short press: Forward the song Short press: Play/pause

Long press: Change mode

Short press: Backward the song

To change the priority behaviour you can use the ”BT UPDATER” Pc Software or the

smartphone “BT SET-APP” application.

Attention: It is possible to control A2DP Stereo music only in “Phone Mode”

Music Share

To start sharing your A2DP music with the passenger already paired on the middle button

(maximum distance 10mt), you must press the “Backward” button long (3 sec.) while the

music is playing.

The passenger must be either in “Phone” or “Intercom” mode without any open audio.

The passenger can only stop the music share pressing short the middle button (but can

not control the music).

The driver can stop the music sharing just pressing again the “Backward” button long.

With music share active you can not keep open the Intercom communication.

GPS Navigator

The GPS Navigator can be paired using the “Volume+” or the “Volume-“ button.

Volume + button (support for stereo A2DP audio and HFP mono)

Volume - button (support for HFP mono audio also in background)

How to pair the BTX1 PRO to a GPS

In general it is possible to pair the BTX1 PRO to all the GPS for motorbike that support

Bluetooth headset connection.

To pair the BTX1 PRO to a GPS, you must ﬁrst enter the setup mode:

1. Turn o the unit

2. Press and hold down the “Middle” button about 7 sec., until the Red light is on per

manently.

3. Now press ﬁrmly (3 sec) the “Volume +” or “Volume -” button, the Blue and Red

light will ﬂash.

4. Enable the Bluetooth device search feature on your GPS

5. After some seconds, “Midland BTX1 PRO” will be displayed on your GPS.

6. Follow the pairing procedure of your GPS. If a pin code is requested you must enter

“0000” (four times zero).

7. When successfully paired, the Blue light of the unit will be on for one second and then

the unit will exit the setup mode and switch to the working mode (the Blue light will

start ﬂashing).

GPS navigator always in background

To keep the intercom open while the GPS gives the street indication you must have the

“background” feature active and the GPS paired on “Vol-” button

Attention: we can’t guarantee this features because is depending on third part device

GPS Stereo (A2DP) voice announcement

BTX1 PRO support Stereo (A2DP) voice announcement from GPS Navigators or smar-

tphone application when paired on “Vol+” button. When a voice announcement “brake

in”, Intercom or FM radio is interrupted to give priority to the announcement itself. By

default this feature is ON; it’s possible to change the priority using the “BT Updater” PC

Software or BT SET-APP smartphone application.

How to listen to the FM Radio

The FM Radio receiver is integrated inside the unit. You just need to switch to the “FM

Radio” mode in order to use it. Long press the middle button until you hear “FM radio”

from the voice announcement. Now all the three main buttons are dedicated to the FM

Radio (See Table).

Press short the Forward or the Backward button to seek the FM Radio station. When

you press long the Forward or the Backward button, you can scan up or down the 6

recorded stations. A voice announcement will tell you the number of which memory you

are entering.

To save the station you are listening, press the Forward and Backward buttons together

for 3 sec. You will hear a beep tone for conﬁrmation.

The station is saved over the last recorded station used.

Thanks to the RDS system, the FM Radio will choose the strongest signal available for

the radio station you like to listen.

The RDS system is OFF by default, if needed you can toggle on/o the RDS pressing

together the “Volume +” and “Volume –“ buttons for 3 sec when the radio is on. A voice

announcement will tell you the RDS status.

Midland BTX1 PRO 2020 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info