Bedienungsanleitung Midland BTX1 (Seite 10 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

494048

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Midland BTX1 - 17

16 - Midland BTX1

Description of the installation brackets

The Midland BTX1 can be ﬁxed onto the helmet in two diﬀerent ways: By either

using the plate with bi-adhesive strip, or the clamp. These methods allow you to

safely “ﬁx” the BTX1 unit onto your helmet and to remove it at any time in order

to recharge or store it.

Plate with bi-adhesive strip

The ﬁxing plate has a bi-adhesive strip on one of

its sides. To ﬁx the plate in place, clean the appli-

cation area on the helmet surface, remove the bi-

adhesive ﬁlm and

place the ﬁxing plate on the helmet by keeping it

contact with the surface for a few seconds.

Screw Clamp

Using the Allen Key, loosen the two screws on the clamp and place the rear plate

between the helmet padding and the external rigid protection. Then, tighten the

two screws in order to ﬁrmly ﬁx the clamp in place. Inside the clamp is included a

small plastic spacer that can be removed to give a tighter ﬁt if required.

Fitting and removing your Midland BTX1

The BTX1 can be easily ﬁtted onto the helmet by sliding it downwards so that

it ﬁts into the slot of the selected ﬁxing device (plate with bi-adhesive strip or

clamp). BTX1 is maintained in position thanks to the ﬁxing clip located on the

upper section (A).

To detach the BTX1, simply press the ﬁxing clip and push the unit upwards.

Switching your Midland BTX1 on and oﬀ

Switching the unit on:

Press and hold “Middle” button down for approximately 3 seconds until the BLUE

indicator lights.

Switching the unit oﬀ:

Press and hold both “Middle” and “Rear” buttons together for approximately 3 se-

conds until the RED indicator ﬂashes 3 times, thus lessening the chances that you

might turn oﬀ the unit accidentally (especially whilst wearing gloves).

Operative “mode”

The BTX1 can operate in two main “mode”: Intercom and Phone.

The 3 multi function buttons can have diﬀerent functionality depending on which

mode the unit is at that moment.

› In “Intercom mode” the middle buttons let you manage the communications

between driver and passanger

› In “Phone mode” you can manage your Bluetooth cellular phone to place/

answer a phone call or to listen to the music (in stereo mode). Please use your

phone responsibly and safely.

You can switch (toggle) from one mode to the other simply pressing the Middle

button for 3 seconds. A voice announcement will tell in which mode you are on.

The toggle sequence is the following:

› Intercom mode (if another unit has been paired)

› Phone mode (if a phone has been paired)

Every time you turn on the unit, the default mode is Intercom (if it was previously

paired to another unit), otherwise it will be Phone (If was paired to a phone).

If you need to know in which mode the unit currently is, just press the “Volume +

“ and “Volume –“ button together. A voice announcement will tell you the current

mode.

How to pair two BTX1 unit

The two units supplied in the same BTX1 box, are already paired and ready to use,

which mean you don’t need to perform this procedure. The unit are already paired

using the Middle button.

If the devices are not part of the same kit, or the units has been purchased sepa-

rately, you need to ﬁrst pair it in order to use it.

To pair the BTX1 to another BTX1 unit

To pair the BTX1 to another BTX1 unit, you must ﬁrst enter the setup mode:

1. Turn oﬀ the unit

2. Press and hold down the middle button about 7 sec., until the Red light is on

permanently.

3. Now press the Middle button for 3 seconds. The Blue and Red light will ﬂash.

4. Do the same procedure on the other unit, When successfully paired, each unit

will have the Blue light on for one second and than go back to the setup mode

(Red light always on).

5. Now the pairing procedure is complete, you just need to exit the setup mode

before you can use the units:

6. Double click on the Middle button, the Red light will turn oﬀ and the Blue

light will start ﬂashing.

You can use now your BTX1.

How to use the Intercom

To use the intercom feature, be sure the both units are turned on and correctly

paired together.

Manual activation

Press the Middle button on one of the two units. Communication is enabled and

remains active until you press again the middle button. The intercom need some

second to activate, you will hear a beep tone when the intercom is open.

Voice activation (VOX)

Simply start talking, after some seconds the communication will be opened and

will remain active for the time you are talking. If there is no conversation the

intercom will be closed after 40 seconds. If needed you can close the intercom

manually without waiting 40 seconds (just press the middle button).

If needed, you can temporarily disable the VOX feature simply by pressing the

Backward button for 7 sec. Two sound beep will advise you when the VOX is di-

sabled. To turn the VOX on again, just press the same button, one beep sound

will advise you that the VOX is now active (or just turn the unit oﬀ and on again).

Adjusting the volume

Your Midland BTX1 uses AGC technology, which automatically adjusts the liste-

ning volume in relation to background noises.

However, it is also possible to manually adjust the volume by means of the “Volu-

me +” and “Volume -“buttons.

Attention: volume can be adjust only when an audio connection is active.

Attention: the volume buttons (Vol + and Vol -) cannot be used to adjust the vo-

lume of the wired audio source. The AGC system with automatically increase the

volume on higher speed.

How to pair the BTX1 to previous Midland BT line unit

The BTX1 is compatible with all the BT line unit from Midland. You can pair the

BTX1 to a BT2, BT1 or BTX1 unit and the max distance of the intercom is deﬁned

from the lower possible.

To pair the BTX1 to another BT line unit, you must ﬁrst enter the setup mode:

1. Turn oﬀ the unit

2. Press and hold down the Middle button about 7 sec., until the Red light is on

permanently.

A- Manual activation

Mode Forward button Middle button Rear button

Intercom Short press: Open/Close intercom to paired

raider

Long press: Change mode

Long press: Toggle on/oﬀ wired

Midland BTX1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland BTX1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info