Bedienungsanleitung Midland BTX1 (Seite 17 von 111) (Holländisch, Portugiesisch, Finnisch)

494048

Zoom out

Zoom in

Vorherige Seite

1/111

Nächste Seite

16 - Midland BTX1

Description of the installation brackets

The Midland BTX1 can be ﬁxed onto the helmet in two diﬀerent ways: By either

using the plate with bi-adhesive strip, or the clamp. These methods allow you to

safely “ﬁx” the BTX1 unit onto your helmet and to remove it at any time in order

to recharge or store it.

Plate with bi-adhesive strip

The ﬁxing plate has a bi-adhesive strip on one of

its sides. To ﬁx the plate in place, clean the appli-

cation area on the helmet surface, remove the bi-

adhesive ﬁlm and

place the ﬁxing plate on the helmet by keeping it

contact with the surface for a few seconds.

Screw Clamp

Using the Allen Key, loosen the two screws on the clamp and place the rear plate

between the helmet padding and the external rigid protection. Then, tighten the

two screws in order to ﬁrmly ﬁx the clamp in place. Inside the clamp is included a

small plastic spacer that can be removed to give a tighter ﬁt if required.

Fitting and removing your Midland BTX1

The BTX1 can be easily ﬁtted onto the helmet by sliding it downwards so that

it ﬁts into the slot of the selected ﬁxing device (plate with bi-adhesive strip or

clamp). BTX1 is maintained in position thanks to the ﬁxing clip located on the

upper section (A).

To detach the BTX1, simply press the ﬁxing clip and push the unit upwards.

Switching your Midland BTX1 on and oﬀ

Switching the unit on:

Press and hold “Middle” button down for approximately 3 seconds until the BLUE

indicator lights.

Switching the unit oﬀ:

Press and hold both “Middle” and “Rear” buttons together for approximately 3 se-

conds until the RED indicator ﬂashes 3 times, thus lessening the chances that you

might turn oﬀ the unit accidentally (especially whilst wearing gloves).

Operative “mode”

The BTX1 can operate in two main “mode”: Intercom and Phone.

The 3 multi function buttons can have diﬀerent functionality depending on which

mode the unit is at that moment.

› In “Intercom mode” the middle buttons let you manage the communications

between driver and passanger

› In “Phone mode” you can manage your Bluetooth cellular phone to place/

answer a phone call or to listen to the music (in stereo mode). Please use your

phone responsibly and safely.

You can switch (toggle) from one mode to the other simply pressing the Middle

button for 3 seconds. A voice announcement will tell in which mode you are on.

The toggle sequence is the following:

› Intercom mode (if another unit has been paired)

› Phone mode (if a phone has been paired)

Every time you turn on the unit, the default mode is Intercom (if it was previously

paired to another unit), otherwise it will be Phone (If was paired to a phone).

If you need to know in which mode the unit currently is, just press the “Volume +

“ and “Volume –“ button together. A voice announcement will tell you the current

mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BTX1 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland BTX1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info