Bedienungsanleitung Midland G12 (Seite 24 von 32) (Englisch)

543256

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

7 Programming frequencies and

CTCSS/DCS codes

7.1 Programming modes

Youcanredeneradiofrequencies(choosingthemamongtheeight

PMR446frequenciesmentionedinpar.5.5.a)factorysetforeachone

of the 16 channels and allocate to each one a CTCSS tone or DCS

code. For further details on the PMR446 frequencies and CTCSS/

DCS consult par. 5.7 and the tables in chapter 11.

Toenterprogrammingmodedothefollowing:

1) Turnoffthetransceiver.

2) Keep the

PTT and SCAN/MON buttons pressed and turn the

device back on. All symbols on the display light up for about one

secondandabeepsoundofconrmationisheard.

3) Whenthedisplaycomesbacktoitsnormalstatus,releasethe

buttons. The display will show the

icon to signal that you

are in programming mode.

Toexitprogrammingmode(andstoresthenewsettings)pressthe

PTT button or turn the device off and then turn it back on.

WARNING! It is advisable to leave the rst eight channels

unchanged so as to keep maximum compatibility with devices of

other manufactures which are normally set in the same way.

7.1.a Setting of radio frequencies and of CTCSS/DCS

1) Gointoprogrammingmodeasdescribedabove(thedisplayshow

).Ontheleftyouwillbeabletoreadtheashingnumber

of the channel and on the right the(smaller)numberequaltothe

radio frequencyprogrammedaccordingtothefollowingtable:

Num. FREQUENCY(MHz) Num. FREQUENCY(MHz)

1 446.00625 5 446.05625

2 446.01875 6 446.06875

3 446.03125 7 446.08125

4 446.04375 8 446.09375

E.g.. 11 3 = channel 11 programmed with radio frequency 3

(446.03125MHz)

2) Pressthe

+ or – button to select the channel to program (from 1

to16).

3) Pressthe

MENU button. The smaller number corresponding to

thecurrentradiofrequencyashesontheright.

4) Ifyouwishtochangetheradiofrequencypressthe

+ or – button

until you have reached the desired frequency.

5) Atthispoint:

• Ifnomorechangingarerequiredgotostep2).

• If you wish to change the frequency of another channel press

twice the

MENU button and repeat operation from step 2.

• If you wish to programme/change CTCSS tone or DCS code

of the currently selected channel carry on with the following

step.

6) Accordingtothepredenedsettingofcurrentlytunedchannel,on

therightthedisplayshows:

• coF or doF - channel is not set with CTCSS or DCS (open

trafc)

• c followed by number XX - the channel has been programmed

with a CTCSS tone with number XX

• d followed by number XX - the channel has been programmed

with DCS code number XX

7) Pressthe

+ or – button to choose desired setting. There are 38

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland G12 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info