Bedienungsanleitung Minolta Vectis 260 (Seite 2 von 4) (Englisch)

42271

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

When your subject is closer than 1.0m/3.28 ft., align the top of your image with the

close-framing guide, using focus hold if necessary.

• The close-framing guide is not visible in P format.

The ready lamp will blink rapidly and the shutter will lock when you are closer than

the focus distance indicated below.

Focal Length Wide Telephoto

Print Format All C or H P

Focus Distance 0.5m - ∞ 0.5m - ∞ 1.4m - ∞

(1.64 ft. - ∞) (1.64 ft. - ∞) (4.59 ft. - ∞)

2 . Insert the battery according to the + and – marks

inside the battery chamber then snap the cover

closed.

• Reset the date and time after installing a new battery.

Each time the camera is turned on, a symbol will appear briefly in the data panel to

indicate the power status of the battery.

Power is sufficient for all camera operations.

Power is sufficient, but the battery will have to be replaced

soon.

Replace the battery. The shutter will lock until the battery is

replaced.

• If no display appears, replace the battery or check that it is

inserted correctly.

Your camera uses IX240 type film designed for use in Advanced Photo System cameras.

• The automatic transport system loads the film, sets the film speed, and advances the film after

each exposure.

• After loading, the film chamber cannot be opened until rewind has been initiated.

• DEP, Double Exposure Prevention, prevents the camera from accepting exposed film.

• This camera will only load film with the ● mark current.

Visual Exposure Indicators

• The current VEI has a white indicator

behind it.

CHECKING THE BATTERY POWER

INSERTING THE BATTERY

Your camera uses one 3-volt CR2 lithium battery to supply

power for all camera operations.

1.Open the battery-chamber door using a coin or

similar object.

1 .Turn the camera upside down and slide the film-

chamber release in the direction indicated.

• The film-chamber door will open partway.

2 .Insert the cassette into the film chamber.

Auto Power Off : To save power, your camera will shut down and retract the lens if it is not operated

for more than eight minutes. Close, then open the front cover again to restore power.

LOADING THE FILM

3 .Press the film-chamber door closed until it clicks.

• The camera automatically advances the film to the

first frame.

• The ISO (film speed) and number of frames remaining on the roll will

be displayed in the data panel.

• Film can be loaded when the camera is on or off.

• If film is loaded with the camera off, all indicators in the data panel

will disappear after the number of frames remaining is displayed.

• Do not load film without an operational battery in the camera.

If blinks in the data panel, open the film chamber, then

remove the film.

- Your camera cannot load a cassette if the current VEI is ◗, ✖, or ■.

- If a processed (VEI ■) or partially exposed (VEI ◗) cassette was

loaded into this camera, the VEI has been changed to ✖.

• If all indicators blink in the data panel, remove and reload the film. If

the film will not load, contact the nearest authorized Minolta Service

F a c i l i t y.

Attach the strap as shown.

ATTACHING THE STRAP FULL AUTO OPERATION

1.Open the front cover to turn the camera on.

• The flash is set to autoflash and will fire when necessary.

2.Select the print format. The viewfinder changes to

match your selection.

Hold the camera steady, making sure your fingers do

not cover the flash. If you are taking a vertically

framed picture, turn the camera so the flash is on

top.

3.Looking through the viewfinder, frame the subject

as desired.

Push the zoom lever toward W to zoom out.

Push the zoom lever toward T to zoom in.

• Do not obstruct the lens barrel.

4.Center your subject in the focus frame, then press

the shutter-release button partway down.

6. Turn the camera off after use by sliding the front

cover closed.

If your subject is located outside the focus frame, you can first lock focus on your

subject, then recompose the picture as desired.

FOR CLOSER SUBJECTS

1.Align the subject within the focus frame and press

the shutter-release button partway down until the

ready lamp glows.

2.Without lifting your finger, recompose the picture

then press the shutter-release button all the way

down to take the picture.

FOCUS HOLD

5.When the green ready lamp glows, press the

shutter-release button all-the-way down to take

the picture.

• Press the shutter-release button with a slow, steady

squeeze, never a quick jab.

Your camera automatically rewinds the film into the cassette after the last

exposure.

1.Wait for the film to completely rewind into the

cassette.

• The frame counter counts down during rewind.

• appears and will blink in the data panel

when the film is rewound.

REWINDING THE FILM

Use manual rewind to rewind the film before the roll is finished.

2. Turn the camera upside down and open the film

chamber.

3.Remove the cassette.

• The film’s VEI indicator will be ✖.

• Do not open the film chamber until the motor stops,

appears, and blinks in the data panel.

1.Gently press the manual-rewind button.

2.Follow steps 1 - 3 from automatic rewind.

• Film cannot be reloaded after it has been rewound.

MANUAL REWIND

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Minolta Vectis 260 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info