Bedienungsanleitung Mitsubishi FD630U (Seite 16 von 46) (Englisch)

493662

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

EN-16

Basic operation (continued)

Power-off

Use the following procedure to turn off the projector.

The lamp may deteriorate if the projector is powered off and on

repeatedly within 30 minutes after the lamp is lighted.

1. Press the POWER button on the control panel or the STANDBY

button on the remote control.

• The message "POWER OFF? YES : PRESS AGAIN"

appears on the screen.

• To cancel, press any button except the POWER button.

(Some buttons on the remote control don’t function for can-

cel.)

2. Press the POWER button on the control panel or the STANDBY

button on the remote control within 10 seconds again.

• The lamp will go out and the STATUS indicator will start

blinking.

• Though the lamp goes out at this second press of the

POWER button (or STANDBY button), the air outlet fans con-

tinue operating for one minute to cool down the lamp. The

STATUS indicator will stop blinking.

• After stopping the air outlet fans, if the temperature inside the

set is still high, the temperature sensor detects it and then

the air outlet fans may start again.

3. Unplug the power cord.

• The POWER indicator will go out.

• If the power cord should be unplugged accidentally while

either the air inlet fan or the air outlet fans are operating or

the lamp is on, allow the projector to cool down for 10 min-

utes with the power off. To light the lamp again, press the

POWER button (or ON button). If the lamp doesn’t light up

immediately, repeat pressing the POWER button (or ON but-

ton) two or three times. If it should still fail to light up, replace

the lamp.

Notice:

• When storing the projector in the carrying case, the lens should

face up.

Before carrying the projector, rotate Focus Ring and Zoom Ring to

adjust the lens to the shortest. This prevents the possible dam-

ages of the lens.

Instant Shut Down

You can turn off this projector just by unplugging the power cord with-

out pressing the POWER button.

• Don't shut down the projector while the STATUS indicator is blink-

ing after the lamp lights up because the lamp's life may be short-

ened.

• Don't turn the projector back on right after shutting it down

because the lamp's life may be shortened. (Wait about 10 minutes

before turning the projector back on.)

• Before shutting down the projector, be sure to close the menu

screen. If you shut down the projector without closing the menu,

the setting data of the menu may not be saved.

• If you shut down the projector while controlling the projector using

the network function, the application software such as Projector-

View may fail. For details, see "LAN Control Utility User Manual"

contained in the CD-ROM.

AUTO POSITION button

When the image supplied from the computer is displaced, carry out

the following procedure.

1. Project a bright image containing as many texts and characters

as possible.

2. When the screen saver has been enabled, disable it.

3. Press the AUTO POSITION button.

The projector automatically makes optimum positional settings

for the input signal.

• When you press the AUTO POSITION button while a signal from a

video device (or signal marked with *2 on page 44) is being input,

a window to select either of the following two adjustment modes is

displayed.

- AUTO ADJUST:

Suitable for signals supplied from a computer.

- VIDEO SIGNAL:

Suitable for signals supplied from a video device such as DVD.

(When you select this mode, the adjustment using the RESO-

LUTION (MEMORIZE) menu (page 24) becomes unavailable.)

Select an appropriate mode using the W or X button and then

press the ENTER button.

• If the projected image is still displaced even after pressing the

AUTO POSITION button several times, refer to the procedure to

adjust computer images. (See pages 27 and 28.)

• When you carry out this procedure with a dark image, the image

may be displaced.

Volume from the speaker

Press the VOLUME S or T button to change the volume

from the speaker.

The volume control bar will appear on the screen.

• The volume control bar will disappear about 10 seconds after the

VOLUME button is released.

• The VOLUME buttons don’t function while the menu selection bar

or the menu is being displayed.

• When a high-level audio signal, such as a DVD audio signal, is

supplied to the AUDIO IN terminal, the output from the speaker

may be distorted.

AV mute

The video and audio signals are temporarily muted when the AV

MUTE button is pressed. To cancel muting, press the AV MUTE button

again.

Setting the aspect ratio

You can change the aspect ratio of the input video signal (or the ratio

of width to height of the image). Change the setting according to the

type of the input video signal.

VOLUME 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi FD630U Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info