Bedienungsanleitung Mitsubishi HSHD2000U (Seite 48 von 80) (Englisch)

31038

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

On LCD Programming

On LCD Programming is a programming method to set the timer recording on the

remote control LCD and transfer it to the VCR. For example, setting the timer

recording of the program on channel 2, on the 12th from 10:00 am to 11:00 am, in

SP mode:

1 Load a tape with its erasure prevention tab intact into the VCR.

2 Press LCD PROGRAM on the remote control. The display for programming

the timer recording will appear on the remote control LCD and CH will flash.

3 Turn the ADJUST dial to choose the channel you would like to record. Turn the

SHUTTLE ring to the right.

• If you are using a cable box that the VCR cannot control, enter the channel

number on which the cable box sends a signal to your VCR (usually channel

3 or 4).

• If you are recording from a DSS

, PRIMESTAR

or DISH Network

™

satellite

receiver, simply choose the channel you would like to record; for example,

channel 245. S will display next to the channel number.

• To record from an external source, press INPUT or turn the ADJUST dial to:

Select L1 for a source connected to the rear panel.

Select L2 for a source connected to the front panel.

4 DAY will flash. Turn the ADJUST dial to choose the day on which you want to

record.

Your choices are:

• a single day up to one month away.

• every day from Monday through Friday; for example, to tape a soap opera.

To program, turn the ADJUST dial until DAILY appears.

• the same day every week; for example, to tape your favorite weekly sitcom.

To program, turn the ADJUST dial until E- (for EACH) and the desired day of

the week appears.

Turn the SHUTTLE ring to the right once you have made your choice.

5 The hour numbers of the start time will flash. Turn the ADJUST dial to set the

hour when recording is to start. Turn the SHUTTLE ring to the right.

6 The minute numbers of the start time will flash. Turn the ADJUST dial to set

the minutes when recording is to start. Turn the SHUTTLE ring to the right.

7 Set the stop time the same way as the start time, using steps 5 and 6.

8 Press SP/EP under the flip cover of the remote control to select the recording

mode.

• select SP if you want to record in SP mode.

• select EP if you want to record in EP mode.

• do not make a selection if you want to keep the recording in the mode that

was previously used.

9 Press TRANSFER. The programmed contents will be transferred to the VCR,

and Recap screen will appear. The program you have chosen to record will be

highlighted.

Make sure that the programming contents shown on the screen is correct.

IMPORTANT

If you cannot select the other program line by turning ADJUST dial on the

remote, press PAUSE first, and then turn the ADJUST dial.

Timer Recording

VCR-A

DAYCH

ON OFF

VCR-A

DAYCH

ON OFF

VCR-A

DAYCH

ON OFF

VCR-A

DAYCH

ON OFF

TRANSFER

VCR-A

DAYCH

ON OFF

¬Program to record

CH DAY ON OFF

10 TH15 9:00p10:30pSP

§ 2 MO12 11:30a 1:30pSP

--- -- --:-- --:-- SP

ππππππππππππππππππππππππ

Use ADJUST to select,

and ENTER.

Press MENU to go back.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi HSHD2000U Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info