Bedienungsanleitung Mitsubishi HSHD2000U (Seite 49 von 80) (Englisch)

31038

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

IMPORTANT

You cannot transfer the program while the VCR is recording or on recording

pause mode.

If you have already programmed 8 recording events, Program memory is full

will appear on your screen for 8 seconds, and then the Recap screen will

appear. Use CANCEL to erase an entry before you can add another one.

If two programmed recording times overlap, VCR is already programmed for

that time will display on your screen for about 8 seconds, and then the Recap

screen will appear. The program you have just set will flash for 3 seconds

and the start time and the stop time will be shown in red letters. The start

and stop time of the overlapped program will be highlighted in red color. You

will need to erase one of them.

If you set the impossible date, The date is wrong. Please re-enter the date.

will be displayed on the screen for 8 seconds.

If the remote control is failed to transfer, The transfer is failed. Please

transfer again will be displayed on the screen for 8 seconds. To transfer the

same programming contents again, press TRANSFER twice. Pressing

TRANSFER once displays the programming contents on the remote control

LCD again, and pressing it again transfers the displayed program.

10 To program additional recording times, follow the procedure from step 2 to 9

again.

11 When you are finished with all programming, check the following:

• If you have a cable box, a digital cable box, a PRIMESTAR

or a DISH

Network

™

satellite receiver, leave the cable box or receiver turned ON.

• If your VCR does not control your cable box, leave the box tuned to the

station you wish to record.

• Turn the VCR power OFF and make sure the programmed recording light is lit.

IMPORTANT

To cancel programming while programming with the remote control LCD,

press LCD PROGRAM.

To cancel programming while displaying the Recap screen, press CANCEL

to cancel the selected program, and then press MENU to exit the Program to

record menu.

Timer Recording Hints

To use the VCR before timer recording begins, press POWER on the remote once.

This turns the programmed recording light off and the VCR on.

If you use POWER on the front panel for this purpose, press it twice. Pressing it

once turns off the programmed recording light; pressing it again turns the VCR on.

When you are finished using the VCR, turn the VCR power off again. Make sure

the programmed recording light is back on.

After a program has been recorded, the VCR memory of that program is cleared

(unless you have scheduled the VCR to record the program every day or every

week).

If there is already a program in the VCR’s memory, you will see the Recap screen

when you bring up the menus for programming to record (unless you are program-

ming with the QUICK PROGRAM). If the VCR’s memory is full, Program memory

is full will appear on the screen. If so, you must erase a program before you can

enter a new one.

Timer Recording

VCR POWER

REC

POWER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi HSHD2000U Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info