Bedienungsanleitung Mitsubishi LU (Seite 14 von 76) (Englisch)

549864

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

EN-14

Setting up your projector (continued)

Correcting skewed or distorted image

For the best projection, project images on a ﬂ at screen

installed at 90 degrees to the ﬂ oor. If necessary, tilt the

projector using the two adjustment feet on the bottom

of the projector.

Adjustment feet

Screen

1. Tilt up the projector to the appropriate angle.

2. Rotate the adjustment feet for ﬁ ne adjustment.

Important:

• Don’t transport the projector with its adjustment

feet extended. Otherwise the adjustment feet may

be damaged.

When ﬁ ne streaks are seen on

projected images

This is due to interference with the screen surface and

is not a malfunction. Replace the screen or displace

the focus a little. (See page 12 for focus adjustment.)

When the projected image is

distorted:

When the projected image is distorted, carry out any

of the KEYSTONE, CORNERSTONE, and CURVED-

mode adjustments to correct the distortion.

When the image distorts in a trapezoid shape, use the

KEYSTONE-mode adjustment. For ﬁ ne adjustment

of the image shape, use the CORNERSTONE-mode

adjustment. To adjust the image projected on a curved

surface, use the CURVED-mode adjustment.

When you press the ENTER/GEOMETRY button on

the projector or the GEOMETRY button on the remote

control, the menu switches in the order of KEYSTONE,

CORNERSTONE, CURVED, regular display, KEYSTONE...

Adjustment using the KEYSTONE mode:

When the screen and the projector are not placed

perpendicularly to each other, projected images

become trapezoidal. If you cannot place them

perpendicularly to each other, press the ENTER/

GEOMETRY button on the projector or the

GEOMETRY button on the remote control to display

the KEYSTONE mode and then press the , ,  or

 button to correct the distortion.

KEYSTONE

SELECT : BLANK

: 0

Every time you press the BLANK button, the

adjustment menu changes as follows:

KEYSTONE  RESET  KEYSTONE ...

KEYSTONE menu

You can correct the distortion vertically or horizontally

focusing on the screen center.

In the following cases (for front projection):

Press the



button.

Press the



button.

Press the



button.

Press the



button.

When you press the  or  button in the RESET

mode, the distortion correction is reset.

Important:

• For proper KEYSTONE-mode adjustment results,

reset the lens to the factory-adjusted position using

LENS SHIFT RESET in the INSTALLATION 1 menu

before carrying out KEYSTONE-mode adjustment.

(See page 34.)

• When the KEYSTONE-mode adjustment is carried

out, the adjustment value is indicated. Note that

this value doesn’t mean a projection angle.

• When the KEYSTONE-mode adjustment takes

effect, the resolution decreases. In addition, stripes

may appear or straight lines may bend in images

with complicated patterns. They are not due to

product malfunctions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi LU Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi LU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info