Bedienungsanleitung Mitsubishi WD-52525 (Seite 43 von 108) (Englisch)

475284

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

[Device] Screen

Figure 15

If you selected “None”, during initial setup, then you

can add a device. If you have added a new device, use

this screen to start learning.

Our examples show the choices for adding a VCR,

however, the same type of screens will appear for any

DBS (Direct Broadcast Satellite), DVD player or Cable

Box.

Edit NetCommand

Add Devices, continued

Choose ONE of these options:

1. Select a recognized manufacturer. The model

number optimized for NetCommand will display at

the bottom of the screen. If a number follows the

manufacturer’s name, (example: Mitsubishi 1), this

indicates additional models are optimized for that

manufacturer. For many device types, non-listed

models will operate in the same way as the listed

models and you can still use the pre-loaded setting.

After selecting Next>, the screens that follow are:

the Name Screen (Figure 18), Connection screen

(Figure 19) and specialized device screens (Figures

20-23), ending with the Finish screen (Figure 26).

2. Select “Other”, then highlight “Learn” and press

ENTER. This will allow you to have NetCommand

learn the remote control signals of this new device.

After selecting “Learn” and pressing ENTER, the

screens that follow are: [Device] Learn screen

(Figure 16), [Device] Advanced Learn screen (Figure

17), Name screen (Figure 18), Connection screen,

(Figure 19) and specialized device screens (Figures

20-23), ending with the Finish screen (Figure 26).

Figure 15. [Device] screen

3. Select “Other”, skip Learn and select Next>. This

will allow the device to appear and will allow

NetCommand to switch inputs to use this device.

However, NetCommand will not be able to control

this device. Later you may use the “Change” option

in the Setup menu to learn the remote control

signals.

After selecting Next>, the screens that follow are:

the Name Screen (Figure 18), Connection screen

(Figure 19) and specialized device screens (Figures

20-23), ending with the Finish screen (Figure 26).

[Device] Learn Screen

Figure 16

Shown only if “Learn” was selected

1. Press ADJUST , , or to select the check

box for each function to be learned.

2. Press ENTER and the function name will begin to

flash to confirm the ready-to-learn status.

3. Press the button on the device’s remote control

that corresponds to the selected function. A check

mark will appear and the function name will stop

flashing. This confirms the signal learned status.

4. To test the learned command, press the ENTER

button on the TV remote, while the learned function

is still highlighted. The device should perform the

selected function. The device needs to be turned

on and the IR emitters properly placed for the

test to be successful (see page 27 for IR emitter

placement).

5. Repeat for each function to be learned.

6. To erase a learned function, highlight the check box

for that function and press CANCEL.

7. When the function signals have been learned,

press ADJUST to select Next> and move to the

[Device] Advanced Learn screen.

NOTE: When learning the device’s remote control

signals, point the device’s remote control at the

TV screen.

Hint: If the device’s remote control uses a single button

for both Power On and Power Off, don’t learn the

Power Off function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-52525 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info