Bedienungsanleitung Mitsubishi WD-62628 (Seite 94 von 124) (Englisch)

475319

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

94 Chapter 7. Troubleshooting

General TV Operation

Symptom Suggested Solution

26. The message “Lamp will soon exceed...” keeps

displaying after the lamp has been replaced.

Reset the lamp reminder in the setup menu.

27. NetCommand unable to learn specific device

keys.

• DevicedoesnotuseIRformatforremotecontrolsignal.ITTandRFformats

cannot be learned.

• Roomlightingmayaffectthesignal.Havetheremotesveryclose(6inchesor

less) to the TV during Learning.

• IfusingaMitsubishiremotecontrol,makesureslideswitchisnotsettoTV

position.

• Some,butnotall,devicekeyfunctionscanbelearnedbyNetCommand.For

example, POWER and PLAY may be learned, but other functions may not

• Thesignalfromtheremotecontrolaynotbestrongenough.Insertfreshbatteries

and try Learning again.

Picture

Symptom Suggested Solution

1. PIP does not display a picture.

• MakesuretheV-Chiplockisoff.

• NotallinputscanbedisplayedasaPIP.

2. Digital channels do not appear in PIP. Normal PIP operation.

3. There is a large black or gray rectangle on the

screen.

The TV’s analog closed captioning has been set to “text”

mode in the Captions menu. Turn off because there is no text

information being broadcast.

4. You cannot see a picture when playing a VHS

tape.

• DisplaytheDeviceSelectionmenuandselectthecorrectVCR.

• CheckyourVCR’sowner’sguideforfurthertroubleshooting.

5. When viewing a stopped VCR, white lines are

rolling on the screen.

• TurnoffvideomutefortheVCR.

• Beginplayingthetape.

• ChangetheVCRinputtotheantennainput.

6. Screen is black when trying to view digital

channels or IEEE 1394 device.

The PerfectColor™ color balance has been incorrectly set.

Press VIDEO repeatedly until you see the PerfectColor option

and press ENTER.

7. A program recorded on your widescreen TV is

distorted when played on a 4:3 TV.

TV was set to Anamorphic when program was recorded.

Record programs in Cropped mode if playing back on a 4:3 TV.

Open the Record menu and select Cropped before making such

a recording.

8. Cannot see a picture from a DV Camcorder. DV formatting was not detected during automatic discovery,

so you must specify it manually. Open the Edit NetCommand

screen, select Change, then select the camcorder, Add, and in

the Name for 1394 Device screen, check mark the DV box.

9. DVCR analog/digital problems. If the tape is currently playing but no picture displays, there may

be a mismatch of the media with the display. Press DEVICE to

display the Device Selection menu. Press ENTER for the DVCR

device. If digital is selected, try analog, or if analog is selected,

try digital.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-62628 Seite 94

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info