Bedienungsanleitung Mitsubishi WD-73C8 (Seite 58 von 94) (Englisch)

475327

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

58 6. NetCommand IR Control (736 and 835 Series TVs)

Several types of A/V receiver control are described here

using the Inputs > AV Receiver menu.

Controlling power and volume is described on this •

page.

For most equipment setups, see “A/V Receiver •

Control: Automatic Audio Switching” on the oppo-

site page.

If your A/V receiver has an HDMI output, you have •

the option of sending both audio and video through

the A/V receiver over a single HDMI cable to the TV.

See “A/V Receiver Control: Automatic Audio and

Video Switching via HDMI,” page 61.

Note: To set up control of other device types, see

“Initial NetCommand Setup for Most Devices,”

page 54.

AV Receiver screen.

Perform NetCommand

IR “learning” for A/V

receiver power and

volume keys.

When the

Power On text starts flashing, aim the

A/V receiver’s remote control at the TV and press

and hold the

POWER

POWER ON

key until a check mark

appears next to Power On.

If the text stops flashing before the check mark •

appears, repeat this step.

To remove the key from NetCommand control, •

press the

CANCEL

key while the key name is

highlighted.

Press the 4. key on the TV’s remote control to highlight

other keys in the list. Repeat steps 2 and 3 for each addi-

tional function you wish to control through NetCommand.

If the A/V receiver has a separate

POWER OFF

key,

press on the TV’s remote to highlight Power Off.

Repeat steps 2 and 3 to “learn” the

POWER OFF

key.

When finished “learning” the power and volume

keys, either press

EXIT

to watch TV or leave the AV

Receiver screen open to continue with NetCom-

mand setup to control switching of A/V receiver

inputs.

Setting Up NetCommand Control of an A/V Receiver

A/V Receiver Control: Power and Volume

Perform this setup to operate the A/V receiver’s power

and volume functions with the TV’s remote control.

To perform this setup you need:

The remote controls for both the TV and the •

A/V receiver.

The IR emitter cable supplied with the TV.•

Before You Begin

Connect your A/V receiver to the TV and any addi-

tional devices. See chapter 3, “TV Connections,”

for suggestions.

Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V

receiver. See “IR Emitter Placement,” page 53.

Set the

TV’s remote control slide switch to the

position and power on the TV if not already on.

Setup to Control A/V Receiver Power and Volume

Open the

AV Receiver screen in one of two ways:

If using the • Auto Output or Auto Input

Sensing screen for the A/V receiver, highlight

the Learn icon and press

ENTER

to open the AV

Receiver screen.

If performing NetCommand setup at any time •

after the A/V receiver has been recognized

through Auto Output/Auto Input Sensing:

Press

, highlight Inputs, and highlight AV

Receiver to open the AV Receiver screen.

The first function highlighted in the

AV Receiver

screen is always Power On. Aim the TV’s remote

control at the TV and press

ENTER

to begin learning

for Power On.

IMPORTANT

To hear audio sent from the TV to the A/V receiver,

you must have:

Physically connected the TV to the A/V receiver •

via the analog or digital audio output.

Assigned, if needed, the name AVR if using an •

HDMI A/V receiver.

Selected the A/V receiver as the audio source. •

Press AUDIO, then

to show the Speakers

option,

then

to select the A/V Receiver.

“•

Learned” the IR codes for the A/V receiver

inputs.

Assigned the TV’s audio output to the correct •

input in the NetCommand A/V Receiver Learn

screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-73C8 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info