Bedienungsanleitung Mitsubishi WD-73C8 (Seite 59 von 94) (Englisch)

475327

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

6. NetCommand IR Control (736 and 835 Series TVs) 59

Setting Up NetCommand Control of an A/V Receiver, continued

Perform one of these setups to enable the A/V receiver

to switch automatically to the correct audio input when

you select a device in the TV’s Input Selection menu.

To set up control of an A/V receiver you need:

The remote controls for both the TV and the A/V •

receiver.

The IR emitter cable supplied with the TV.•

Connecting cables•

Two different setups are described here. Review the

descriptions to find the setup needed for your equipment.

Audio Available from TV only•

Audio from

ANT 1

and

ANT 2

must be sent to

the A/V receiver from the TV’s DIGITAL AUDIO

OUTPUT or analog

AVR AUDIO OUTPUT

Use Setup 1 to make the A/V receiver switch to its

designated TV audio input when viewing these sources.

Analog Stereo Audio•

Audio from sources with only analog stereo output

(such as a VCR) can be sent either directly to the

A/V receiver or through to the TV and then on to the

A/V receiver.

Mitsubishi recommends you send audio through

the TV as shown in the example. Setup 1 causes

the A/V receiver to switch to its input designated for

TV audio.

If you have a digital A/V receiver, the TV makes the

audio available by converting analog audio to a

digital output.

HDMI Digital Stereo Audio•

Digital stereo audio from an HDMI connection

is available both in digital format (from the TV’s

DIGITAL AUDIO OUTPUT jack) and in analog

format (from the TV’s

AVR AUDIO OUTPUT

jack).

Audio Switching Setup 1: Audio to the A/V receiver

from the TV’s digital or analog audio output

Note: This setup is required to hear digital sur-

round sound

A device can send digital surround sound such as

Dolby Digital or DTS directly to the A/V receiver,

bypassing the TV entirely. The device might be a DVD

player, cable box, or satellite receiver, and could have

HDMI output. A DVD player is used in this example.

Your setup may include additional devices with digital

surround sound connected directly to the A/V receiver.

These devices might be a DVD player plus a cable box

or satellite receiver.

BVEJPWJEFP

*ODPNJOH

$PBYJBM

$BCMF

"73FDFJWFS

%7%BVEJP

JOQVU

%7%1MBZFSXJUI

%JHJUBM4VSSPVOE4PVOE

WJEFP

EJHJUBMTVSSPVOETPVOE

WJEFP

BOBMPHBVEJP

%7%1MBZFS

XJUI

%JHJUBM

4VSSPVOE

4PVOE

Audio Switching Setup 2: Audio from a device

providing surround sound is sent directly to the A/V

receiver.

audio + video

Incoming Coaxial Cable

to ANT 1/ANT 2

A/V Receiver

DVD audio

input

TV audio input

TV audio

out

audio output from

TV (digital or analog)

video

analog audio

VCR with

Analog Audio Output

Audio Switching Setup 1: Automatic A/V Receiver

Switching to TV Audio Input

Audio Switching Setup 2: Automatic A/V Receiver

Switching to a device sending audio directly to the A/V

receiver. You must use setup 2 to hear digital sur-

round sound from the source device.

Note: Automatic audio and video switching over an

HDMI cable is covered on page 61.

A/V Receiver Control: Automatic Audio Switching

Audio Switching Setup 1: Audio

from TV’s Audio Output

Audio Switching Setup 2: Audio from Source Device

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-73C8 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info