Bedienungsanleitung Mitsubishi WD390U-EST (Seite 14 von 69) (Englisch)

549869

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

EN-14

Preparation

Preparation for projection

1. Attach the provided power cord to the projector.

2. Plug the power cord in the wall outlet.

3. Remove the lens cap.

Warning:

• Donotlookintothelensdirectlywhentheprojector

is on.

• Thelenscapisforprotectingthelens.Ifyouleave

the lens cap on the lens with the projector turned

on, it may be deformed because of heat build-

up. Remove the lens cap when you turn on the

projector.

• OneofpowercordsfortheU.S.,Europe,

U.K., Australia, and South Korea is provided

appropriately.

• Thisprojectorusesthepowerplugofthree-pin

grounding type. Do not remove the grounding pin

from the power plug. If the power plug doesn’t ﬁt

your wall outlet, ask an electrician to change the

wall outlet.

• IncasethatthepowercordfortheU.S.isprovided

with this projector, never connect this cord to any

outlet or power supply using other voltages or

frequencies than rated. If you want to use a power

supply using other voltage than rated, prepare an

appropriate power cord separately.

• Use100-240VAC50/60Hztopreventreor

electric shock.

• Donotplaceanyobjectsonthepowercordor

do not place the projector near heat sources to

prevent damage to the power cord. If the power

cord should be damaged, contact your dealer for

replacement because it may cause ﬁre or electric

shock.

• Donotmodifyoralterthepowercord.Ifthepower

cord is modiﬁed or altered, it may cause ﬁre or

electric shock.

Caution:

• Pluginthepowercordrmly.Whenunplugging,

hold and pull the power plug, not the power cord.

• Donotpluginoroutthepowercordwithyour

hand wet. It may cause electric shock.

• Whenyoumovetheprojector,turnoffthepower,

unplug the power cord from the wall outlet, and

then remove the connected cords. Otherwise, the

power cord may be damaged, resulting in ﬁre or

electric shock.

• Ifdustormetallicsubstanceisonoraroundthe

pins of the power plug, unplug the power cord and

clean it using a dry cloth. If you continue to use the

projector without cleaning, it may result in ﬁre or

electric shock. Clean the power plug periodically at

least once a year.

• Besuretounplugthepowercordfromthewall

outlet if the projector will not be used for a long

period of time. Otherwise, it may cause ﬁre.

Important:

• WhenStandbyModeintheInstallationmenuis

set to LAN, Speaker Out, or Monitor Out, the fans

rotate at very low speed during standby after

plugging the power cord (with 5 second high speed

rotation at the beginning) and after turning off the

lamp. This is to cool down the projector operating

various functions during standby and is not a

malfunction. (When Standby Mode is set to Low,

the fans stop during standby.)

Adjustment of the projection angle

For the best projection, project images on a ﬂat screen

installed at 90 degrees to the ﬂoor. If necessary, tilt the

projector using the two adjustment feet on the bottom

of the projector.

Using the adjustment feet (front)

1. Tilt up the projector to the appropriate angle.

2. Rotate the adjustment feet (front) for ﬁne

adjustment.

Important:

• Installthescreenonaatwallat90degreestothe

ﬂoor.

• Slantingtheprojectormorethan±10°(rightand

left)or±15°(frontandrear)maycausetroubleor

explosion of the lamp. You can tilt the projector up

to 8 degrees using the adjustment feet only.

• Imagesmaynotbeprojectedinashapeofa

regular rectangle or with its aspect ratio 4:3,

depending on the installation conditions of the

projector and the screen.

When projected images are

distorted to a trapezoid

When Auto Keystone in the Installation menu is set

to On, this projector automatically corrects vertical

keystone distortion. For ﬁne adjustment, press the

KEYSTONE button on the projector or the remote

control to display Keystone, and adjust the image by

pressing the ,  button (or VOLUME ,  button

on the remote control).

In the following cases:

Press the



button. Press the



button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD390U-EST Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi WD390U-EST

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info