Bedienungsanleitung Mitsubishi WS48515 (Seite 91 von 100) (Englisch)

32985

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

18. TV functions do not respond to the remote

control or to front panel control and will not

Power Off.

• Use the System Reset button as explained at the end of this

section.

19. Name options not available for some channels • Only memorized analog channels can be named.

20. When viewing a stopped VCR, white lines are

rolling on the screen.

• Turn off video mute for the VCR.

• Begin playing the tape.

• Change the VCR input to the antenna input.

21. TV turned itself Off and the light on the Front

Panel started to blink.

• Momentary power fluctuation caused the TV to turn off to prevent

damage. Wait for the green light to stop flashing and turn On again.

• If the TV does not stay turned On, use the System Reset

button. If this happens frequently, obtain an AC line power

conditioner/surge protector.

22. When a Device is selected from the Device

Selection menu, the screen is blue

(no signal source).

• Make sure the selected device is turned on.

• From the Edit NetCommand® menu select Review setting. Verify that

the inputs are actually connected to the TV . If they are not, either

change the physical connections on the back panel, or select the

Change setting on the Edit NetCommand menu to change the TV

NetCommand’s settings for the connection.

23. The Device does not respond to button presses

from the remote.

• Remote has not been setup for NetCommand

use.

• The incorrect manufacturer was selected during setup.

Select the Change setting from the Setup menu and then the device

to display the manufacturer selection. Change if necessary.

• The device is not supported and keys have not been learned.

• The requested function is not supported by NetCommand.

Verify that the function is supported or keys are learned.

• The IR emitter is incorrectly placed. Make sure the IR emitter is

facing the IR sensor in the device.

• The IR emitter is not plugged into the IR emitter Output

NetCommand.

• The IR emitter is facing the TV screen, causing double signals. Be

sure that the IR emitter cannot send to the TV.

24. The A/V Receiver is the selected audio source

but there is no sound.

• Check to see if the A/V Receiver power is turned on. After the power

is turned on, redisplay the Device Selection menu and press ENTER

to allow NetCommand to correctly select the A/V Receiver input.

• From the Setup Menu select Review setting. Check the Review

screen to see if the A/V Receiver inputs and device correspond to the

actual connections on the A/V Receiver. If they do not match, either

change the actual connections, or select Change on the Edit

NetCommand menu to change the device on the Connection screen.

25. The TV Speaker icon or A/V Receiver icon is

grayed out and not selectable.

• Select the Change setting from the Edit NetCommand menu, and

then select the device (for example VCR). Once the Connection

screen is displayed, check if the audio checkbox is selected for the

TV input and/or AVR input.

26. Devices are grayed out in the Device Selection

menu or the PIP Selection menu.

• A recording is in progress requiring the use of Monitor Out. Cancel

the recording to select the device.

• Digital devices (Digital channels,1394 devices and Memory cards)

cannot display in the PIP or POP.

27. Cannot see the A/V Receiver menu. • The A/V Receiver is not connected to any input of the TV. To check

the A/V Receiver menu temporarily plug into an unused input of the

TV. Then select Review from the Setup Menu, turn the input On to

view the A/V Receiver menu.

28. Screen is black when trying to view digital

channels or IEEE 1394 device.

• The PerfectColor™ color balance has been incorrectly set. Use the

Setup menu to reset the color balance.

29. The REC button is not working, or, on the

Transport menu the record key is grayed out and

not available.

• The device does not support recording, such as a DVD player.

• Recordings can not be initiated from the Transport menu when

using an IEEE 1394 device. Press REC instead. The Record

menu displays allowing setup of a recording.

Problem Possible Solution

Troubleshooting, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WS48515 Seite 91

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info