Bedienungsanleitung Mitsubishi XD520U (Seite 12 von 34) (Englisch)

493631

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

EN-12

Preparation

Preparation for projection

1. Attach the provided power cord to the projector.

2. Plug the power cord in the wall outlet.

3. Remove the lens cap.

Warning:

• Do not look into the lens directly when the projector is on.

• The lens cap is for protecting the lens. If you leave the lens cap on

the lens with the projector turned on, it may be deformed because

of heat build-up. Remove the lens cap when you turn on the pro-

jector.

• One of power cords for the U.S., Europe and U.K. is provided

appropriately.

• This projector uses the power plug of three-pin grounding type. Do

not remove the grounding pin from the power plug. If the power

plug doesn’t fit your wall outlet, ask an electrician to change the

wall outlet.

• In case that the power cord for the U.S is provided with this projec-

tor, never connect this cord to any outlet or power supply using

other voltages or frequencies than rated. If you want to use a

power supply using other voltage than rated, prepare an appropri-

ate power cord separately.

• Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.

• Do not place any objects on the power cord or do not place the

projector near heat sources to prevent damage to the power cord.

If the power cord should be damaged, contact your dealer for

replacement because it may cause fire or electric shock.

• Do not modify or alter the power cord. If the power cord is modified

or altered, it may cause fire or electric shock.

Caution:

• Plug in the power cord firmly. When unplugging, hold and pull the

power plug, not the power cord.

• Do not plug in or out the power cord with your hand wet. It may

cause electric shock.

Adjustment of the projection angle

For the best projection, project images on a flat screen installed at 90

degrees to the floor. If necessary, tilt the projector using the two

adjustment feet on the bottom of the projector.

Using the adjustment feet (front)

1. Tilt up the projector to the appropriate angle.

2. Press the foot adjustment button (front).

3. Release the foot adjustment button (front) after fine adjusting a

position of lengthwise direction of the image.

After using the projector:

4. Put the adjustment feet (front) back into the projector by pressing

the foot adjustment buttons.

Using the adjustment feet (rear)

1. Tilt up the projector to the appropriate angle.

2. Rotate the adjustment feet (rear) for fine adjustment.

Important:

• Install the screen on a flat wall at 90 degrees to the floor.

• Slanting the projector more than ±10° (right and left) or ±15° (front

and rear) may cause trouble or explosion of the lamp. You can tilt

the projector up to 8 degrees using the adjustment feet only.

• Images may not be projected in a shape of a regular rectangle or

with its aspect ratio 4:3, depending on the installation conditions of

the projector and the screen.

• To correct vertical keystone distortion, press the KEYSTONE but-

ton on the projector or the remote control to display KEYSTONE,

and adjust the image by pressing the S, T button (or VOLUME

S, T button on the remote control).

In the following cases:

Important:

• When the keystone adjustment is carried out, the adjustment

value is indicated. Note that this value doesn’t mean a projection

angle.

• The allowable range of the adjustment value in the keystone

adjustment varies depending on the installation conditions.

• When the keystone adjustment takes effect, the resolution

decreases. In addition, stripes may appear or straight lines may

bend in images with complicated patterns. They are not due to

product malfunctions.

• Noise may appear on the screen during the keystone adjustment

because of the type of the video signal being projected and the

setting values of the keystone adjustment. In such cases, set the

keystone adjustment values in the range where the image is dis-

played without noise.

• When the keystone adjustment is carried out, the image may not

be displayed correctly because of the type of input signal.

foot adjustment button

Press the T

button.

Press the S

button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi XD520U Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info