Bedienungsanleitung Mitsubishi XD520U (Seite 13 von 34) (Englisch)

493631

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

EN-13

ENGLISH

Basic operation

Power-on

1. Turn on the device connected to the projector first.

2. Plug the power cord in the wall outlet.

• The POWER indicator lights up.

• If the power cord is unplugged from the wall outlet before the

projector is cooled down completely after use, the fans may

start rotating when the power cord is plugged in next time

and the POWER button may not function. In this case, wait

for the fans to stop and press the POWER button to light the

indicator.

3. Press the POWER button on the control panel or the ON button

on the remote control.

• It may take about one minute for the lamp to light up.

• The lamp occasionally fails to light up. Wait a few minutes

and try to light the lamp again.

• After the POWER button is pressed, the image may flicker

before the lamp becomes stable. This is not a product mal-

function.

• Regardless of the setting of LAMP MODE in the INSTALLA-

TION menu, the STANDARD lamp mode is activated by

default. The LAMP MODE is set to either STANDARD or

LOW depending on the setting last selected, and you cannot

switch the LAMP MODE in about one minute after the lamp

is on.

Important:

• Do not cover the lens with the lens cap while the lamp is on. Do

not strip off the aluminum sheet inside the lens cap.

• The projector starts warming up when the POWER button is

pressed. During the warm-up process, images may appear dark

and no commands are accepted.

• By blinking red, the STATUS indicator indicates that the lamp

should be replaced soon. Replace the lamp when the STATUS

indicator blinks red. (See page 27 and 30.)

• Images may not be projected with good quality in an extremely hot

or cold environment. (This is not a product malfunction.)

4. Adjust the focus by turning the focus ring.

5. Choose your desired external input source using the COM-

PUTER or VIDEO button.

• The input source is switched from VIDEO to COMPUTER at

the press of the COMPUTER button on the control panel.

• The input source is switched between VIDEO and S-VIDEO

at every press of the VIDEO button on the control panel.

• The projector automatically selects the appropriate signal

format. The selected signal format is displayed on the

screen.

• The COMPUTER and VIDEO buttons don’t function while

the menu is being displayed.

• When COMPUTER is chosen as the source, images sup-

plied from the computer may flicker. Press the W or X button

on the remote control to reduce flicker, if it occurs.

• To avoid permanently imprinting a fixed image onto your pro-

jector, please do not display the same stationary images for

long period.

6. Adjust the image size by turning the zoom ring.

• If necessary, adjust the focus and zoom again.

When fine streaks are seen on projected images

This is due to interference with the screen surface and is not a mal-

function. Replace the screen or displace the focus a little.

1, 2

5 5

3, 1, 2

STANDBYON

ASPECTMAGNIFY

KEYSTONE

VOL PAGE

FREEZE

AUTO

POSITION

MUTE

ENTER

COMPUTER

VIDEO

VIEWER

UNPLUG

VIDEO

POWER

FOCUS

ZOOM

Indicator

Condition

STATUS POWER

Stand-by - Red

When the lamp is on. Green Green

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi XD520U Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info