Bedienungsanleitung Montiss CSC5623M (Seite 21 von 51) (Deutsch, Englisch, Holländisch, Französisch)

481109

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

USE OF ACCESSORIES

English

Steam-output indicator (Illustration 3)

With the steam-output indicator you can determine the steam emission. It is possible to set the

output of steam between MIN (minimum); no steam and MAX (maximum).

Should no steam be emitted from the unit during use, then check:

- The setting of the steam-output indicator.

- If the unit has been switched on and has reached the selected temperature.

- If the steam output has been locked (see “Safety Lock”)

- If all the connecting pieces have been properly assembled.

- If the steam hose has been properly attached to the unit.

Should the above-mentioned check not result to release of steam, please switch the device off and

pull the plug from the wall socket. Let the device cool down completely and then check if there is

water in the tank. If not, please fill the unit as described at the header “filling the water tank”.

Should there be sufficient water in the tank, please start using the device once more. If there is

still no steam coming from the unit, then please contact us.

Steam Gun (Illustration 4)

Before you can start using the device, please ensure the steam hose has been connected to the

unit correctly. You can also do this after you have fixed accessories to the steam gun. Pull down

the lid of the steam socket at the front and insert the hose in a proper manner by lining up the 4

ridges. Push the two pieces well into each other.

The cleaner is ready for use when the yellow steam ready switches off. Ensure that the safety lock

on the steam gun is off. When you press the trigger on the steam gun, steam will be emitted from

the nozzle. Direct the steam gun at a cloth first, until the steam is emitted evenly. Now keep the

trigger pressed, and direct the steam jet at the surface to be cleaned, removing the dirt by moving

the steam jet to and fro over the surface. The steam jet will stop as soon as you release the steam

trigger.

Safety Lock (Illustration 5)

When the safety lock is pushed to the forward position, the steam switch cannot be pressed. Push

the lock to the rear position to release the steam switch.

In order to ensure safe use, even in case of accidental contact with liquids, the steam gun is

isolated from the electrical power supply (zero-volt system).

When cleaning surfaces with the steam gun, wipe the surface dry afterward using a micro-fibre or

cotton cloth if necessary; this will also remove any excess moisture for thorough cleaning. In order

to control the steam output and cleaning power at the surface, move the steam gun closer to or

further away from the surface. Do not hold the steam gun concentrated for too long on a single

spot.

Extension tubes (Illustration 6)

Depending on the task in hand, you can fit one, two or three extension tubes. Push the extension

tube onto the connection nozzle as far as it will go until you hear it click into place. Then attach

the floor head.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Montiss CSC5623M Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info