Bedienungsanleitung Morphy Richards Redefine (Seite 11 von 84) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Spanisch, Türkisch)

588260

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Sound

The audible signals from your Hot Water Dispenser can be

turned on or off. Press and hold the Temperature Button (4)

for 2 seconds to switch the sounds on or off.

Standby

Your Hot Water Dispenser will enter Standby Mode to save

power 60 seconds after the end of the heating and dispense

cycle. The unit enters standby mode after 60 seconds

of inactivity if a heat and dispense cycle hasn’t been

completed. To wake the unit, press any button or rotate the

Water Volume Dial (2).

The Hot Water Dispenser can be placed in standby mode by

pressing the Start/Stop Button (1) for 2 seconds.

Any water remaining in the Heating Chamber when your Hot

Water Dispenser enters stand by will need to be dispensed

upon exiting standby, or reheated and dispensed before a

new volume or temperature can be selected.

Drip Tray 16

The Drip Tray Indicator (10) indicates that the Drip Tray (8)

is full and must be emptied. To empty, pull the drip tray

outwards until it is free from the runners and

discard the contents. CAUTION! The contents of the drip tray

may be hot. Replace the Drip Tray once emptied ensuring

the Drip Tray Cover (9) is replaced correctly.

Descale 17

This product is ﬁtted with a concealed element that must be

descaled when the Descale Icon (16) illuminates. Excessive

scale can cause the product to switch off before the end of

the heating cycle and may damage the element invalidating

the warranty.

Remove hard scale using a proprietary descaling product.

We recommend Oust Descaler (please follow the instructions

carefully) which may be purchased from our Helpline or from

your local retailer.

To descale the unit:

1 Remove the BRITA Hopper (21) and MAXTRA cartridge

(19) from the Water Tank (7).

2 Fill the Water Tank to the MAX line with cold water add

the Oust Descaler as per manufacturers instructions.

3 When the crystals have dissolved, set the unit to heat

1.5 litres of water to 85 degrees.

Do not boil to 100 degrees

4 Leave the Hot Water Dispenser for 10 minutes.

Do not dispense the water!

5 After 10 minutes, dispense the water from the Heating

Chamber into a vessel and discard.

6 Empty the water tank and rinse thoroughly with cold

water.

7 Fill the water tank to the MAX line with cold water, set

the unit to boil 1.5 litres to 100 degrees and dispense

the water. Discard the water and repeat the cycle 3 times

8 Replace the BRITA Hopper and MAXTRA cartridge into

the Water Tank. Fill with fresh water.

9 Press and hold the Start / Stop Button (1) and Dispense

Button (5) for 5 seconds to reset the descale time. The

descale icon will extinguish. The Hot Water Dispenser

will reset and the unit will return to ready mode.

10 After 60 seconds of inactivity the Hot Water Dispenser

will enter standby.

Cleaning

Wipe the outside with a damp cloth.

WARNING: Always disconnect the plug from the

mains and allow the appliance to cool before cleaning.

IMPORTANT: Do not use abrasive cleaners on the

outside of the appliance, as they may scratch the

surface.

∂

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morphy Richards Redefine Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info