Bedienungsanleitung Morso 2800 series (Seite 25 von 36) (Englisch, Dänisch)

744380

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

If you have a brick chimney with a large aperture, we recommend that you install an insulat-

ing chimney liner of the proper diameter. This will increase the draught, and improve the

fuel economy.

There are no requirements with respect to specic chimney heights, but a chimney must

be tall enough to provide a good draught, and to ensure that the smoke does not cause any

problems. As a general rule, there will be a satisfactory draught if the chimney extends 4

metres above the stove and at least 100 cm above the spine of the roof.

If the chimney is located along the side of the house, the top of the chimney should never

be lower than the spine of the roof or the highest point on the roof. Please note that there

are often national and local regulations concerning the location of chimneys in houses with

thatched roofs. Please see section 1.9 on Draught.

The chimney and the ue pipe must be tted with cleaning doors, which must be at least

the same size as the chimney’s aperture area.

The chimney must be accessible for external inspection, and it must be possible to access

the cleaning doors and the chimney if it is to

be cleaned from the top

(e.g. steel chimneys).

1.6 Connecting the ue pipe

Lift the upper cast iron top plate o the

stove.

Note: The included round cast iron

cover plate must be mounted on the

upper cast iron top plate if the stove is being

installed with the ue pipe to the rear.

Mounting the ue collar pointing up-

wards

From the factory, the stove is prepared

for installation with the included ue collar (1)

pointing upwards with included ball stop and

screws. The ball stop, which prevents the

chimney sweep from damaging the

stove’s bae plates while sweeping, is the

145 mm long rod that is provided.

Mounting the ue collar to the rear

If the stove is being installed with the

ue pipe to the rear, the round plate

fixed with two screws on the back of the

stove is dismounted. The iron piece on

the inside convection back panel is knocked

out with light, rm taps with a hammer next to the small ”bridges” holding the piece.

The cast iron cover is removed from

the back panel and mounted on the top plate. The ue collar is centred and screwed onto

the back of the stove with the clamps and screws provided. The ball stop is not used when

installing the ue collar to the rear.

The location of the baes

The baes (2) and (3), which are made from vermiculite, are mounted at the factory.

Make sure that the baes are correctly assembled before lighting the stove

(please see the sketch).

45°

SECTION

A-A

SCALE

1 : 10

Zone:

Rev.:

Description

Date

Sign.:

Revisions

Title:

Drawing no.:

1:20

Afstand til brændbart

og snit

Morsø 2800

5766,94

Date of print: 29-06-2018

2800-67 a

Itemno.:

This drawing is Morsø Jernstøberi A/S' property and must not be sold, lended or copied without any written authorization from the company.

Material:

Weight kg.:

Model no.

Drawingtype:

Location of file:

Scale:

Format:

Released:

Construction:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso 2800 series Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 2800 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info