Bedienungsanleitung Morso 3100 series (Seite 14 von 19) (Englisch, Dänisch)

744324

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

DK ENG

2.0 Firing/using the stove

The heat output of your stove is regulated by means of the air inlets. The primary air supply,

i.e. the air which passes through the shaking grate, is controlled by the air control on the

door, while the secondary air supply, i.e. the air supplied to the re across the glass window,

is controlled by the air control lever under the ash lip.

vThe stove’s rated heat output is 5,2 kW. The eciency is 81%.

Your new Morsø stove is EN-tested and recommended to be red with wood. The stove is

equipped with a removable handle; for safety reasons it should be removed during use, espe-

cially where children are nearby.

NB!

Wood is a material that contains a great deal of gas (approx. 75%). The gases are released

when the wood is lit and heated. For this reason, it is important that these gases are ig-

nited quickly after stoking. If the wood just lies smouldering, especially after re-stoking,

a lot of smoke is created which, in the worst case, may cause an explosive ignition of the

gases, resulting in damage to the stove.

In order to ignite the gases that are released from the wood, and to keep clear, lasting

ames during the combustion process, it is important to let in the required quantity of

oxygen (air supply) at all times. The setting of the air supply, the method of ignition and

the lighting intervals depend on the draught in the chimney, the wind and weather, the

amount of heat required, the fuel, etc. This means that it may take some time before

you get to know the correct functioning of the stove under any given circumstances.

Although you can re your Morsø stove with almost all kinds of wood, you should

not re with wet wood, or unseasoned wood. Wood ought to be stored under a roof

for at least 1 year, and preferably 2 years, with free access to wind. Wood should be

chopped as soon as possible after felling if it is to dry quickly. The wood can be used

once the moisture is less than 20%. During the test, all stoves are tested with wood

with a moisture content of (16 ± 4)%.

Never use driftwood as it usually has a high salt content, which damages both

the stove and the chimney. Impregnated and painted wood and chipboard emit

poisonous smoke and fumes so they should not be used as fuel either

Please note that liquid fuel may not be used in the stove.

Pieces of wood with a diameter exceeding 10 cm should always be chopped. The pieces

of wood should be short enough to be able to lie at over the layers of embers, with air

at both ends. The maximum length of fuel in the stove is 30 cm. The maximum quantity

of fuel is approx. 2 kg/hour (max. 2 pieces of wood each time you re-stoke).

The rst few times you light the stove, the re should be moderate so that the heat-

resistant paint can harden before ring more vigorously. During the hardening phase,

the paint may develop obnoxious smoke and smell the rst time it is lit, which is very

normal. Make sure that the room is well ventilated during this period.

When heating up or cooling down, the material is exposed to major temperature

dierences that may cause the stove to give o creaking sounds.

2.1 Lighting instructions and fuelling intervals

A lot of air is needed when lighting the stove. If you are starting with a cold stove, the door

should be left ajar for the next few minutes, and the primary air supply opened to maximum

(the handle under the ash shelf). When ring with wood, the riddling grate must be closed,

i.e. the riddling lever must be pushed all the way in. When draught is poor, letting in a little

air through the grate may facilitate ring; however, it should be noted that this supply of air

may cause temporary sooting of both stones and glass. If a starting device is used, the rid-

dling grate must be opened a little by pulling out the riddling lever.

In order to build up an insulating layer of ash in the bottom of the stove, you should burn 1-2

kg of dry kindling when you light the stove the rst time. Always keep approx. 1 cm ash at

the bottom of the combustion chamber.

1. A layer of embers will form rapidly if the stove is lit with

2 - 4 re lighters or 7 - 10 rolled up sheets of newspaper,

underneath roughly 1-2 kg of dry kindling.

2. Fully open the primary and secondary air supplies that

is controlled with the handle beneath the ash lip.

3. After the paper/re lighters have caught re, leave the

re door ajar about 2-3 cm, so that the chimney draws well.

4. After 5-10 minutes the chimney draft should be estab-

lished, at this point close the re door. If all the necessary

conditions are met, a nice layer of embers will start to ac-

cumulate after another 15 - 20 minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso 3100 series Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 3100 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info