Bedienungsanleitung Moto Guzzi MGS Corsa (Seite 13 von 157) (Englisch)

551116

Zoom out

Zoom in

Vorherige Seite

1/157

Nächste Seite

STRUCTURE

Sect. 1 - GENERAL INFORMATION

MGS corsa user's manual - page 1-7

DANGER

Never reuse a circlip or snap ring. These parts must always be renewed once they have been

disturbed.

When fitting a new circlip or snap ring, take care to move the open ends apart just enough to allow

fitting to the shaft.

Make it a rule to check that a newly-fitted circlip or snap ring has located fully into its groove.

Never clean a bearing with compressed air.

CAUTION All bearings must rotate freely with no hard spots or noise. Replace any bearings that do not meet these

requirements.

- Use ORIGINAL Moto Guzzi spare parts only.

- Use the specified lubricants and consumables.

- Where possible, lubricate a part before assembly.

- When tightening nuts and bolts, start with the largest or innermost nut/bolt and observe a cross pattern. Tighten

evenly, in subsequent steps until achieving the specified torque.

- Replace any self-locking nuts, gaskets, seals, circlips or snap rings, O-rings, split pins, bolts and screws which

have a damaged thread.

- Lubricate the bearings abundantly before assembly.

- Make it a rule to check that all components you have fitted are correctly in place.

- After repairing the motorcycle and after each service inspection, perform the preliminary checks, and then

operate the motorcycle in a private estate area or in a safe area away from traffic.

- Clean all mating surfaces, oil seal edges and gaskets before assembly. Apply a thin layer of lithium grease along

the edges of oil seals. Fit oil seals and bearings with the marking or serial number facing outwards (in view).

ELECTRICAL CONNECTORS

To disconnect the electrical connectors, follow the procedures below. Failure to comply with these procedures may

lead to irreparable damage to the connector and the wiring as well.

If present, press the special safety hooks.

WARNING

Do not pull cables to disconnect the two connectors.

• Grasp the two connectors and disconnect them by pulling them in the two opposite directions.

• In case of dirt, rust, moisture, etc.., thoroughly clean the inside of the connectors with compressed air.

• Make sure that the cables are correctly fitted inside the connector terminals.

CAUTION The two connectors have just one correct positioning. Make sure to position them in the right direction.

• Then fit the two connectors. Make sure they are correctly coupled (a click will be heard if hooks are present).

TIGHTENING TORQUE SETTINGS

DANGER

Always remember that the tightening torque settings of all wheel, brake, wheel shaft and other

suspension parts play a fundamental role to ensure vehicle safety. Make sure that these values are

always within the specified limits.

Check fastening parts tightening torque settings at regular intervals. Upon reassembly, always use a

torque wrench.

Failure to comply with these recommendations could lead to the loosening and detachment of one of

these parts with a consequent locking of the wheel or other serious troubles affecting the vehicle

manoeuvrability, and thus the risk of falls and serious injuries or death.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Moto Guzzi MGS Corsa Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info