Bedienungsanleitung Motorola ML25254 (Seite 22 von 36) (Englisch)

779576

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

8.6 Switching Between the Speakerphone, Handset and Headset Mode

1. To switch to the speakerphone mode, press s. The speakerphone indicator illuminates. Place

the corded handset back into the cradle.

2. To switch to the corded handset, pick up the handset. The speakerphone or wired headset

indicator will turn o.

3. To switch to the headset, press HEADSET to enable the headset, and the headset indicator

illuminates.

8.7 Mute

To have a private, o-line conversation, use the Mute feature. The party on the other end of the

line cannot hear you, but you can still hear them.

1. During a call, press MUTE to activate the Mute feature.

2. Press MUTE again to de-activate.

NOTE

The Mute LED indicator will illuminate when the Mute feature is activated.

8.8 Do Not Disturb (DND)

This feature will disable your telephone’s ringer for a set period of time to prevent incoming calls

from interrupting. When an incoming call or intercom call occurs, the status indicators will light up

but the phone will not ring.

1. In idle mode, press DND/PRIVACY. The last setting is displayed.

2. Using VOL + and VOL - of the navigation button to scroll to your selection. You can choose

from as short as

15 MINUTES, 30 MINUTES, 45 MINUTES, 1 HOUR

2 HOURS

and increase the

duration by 1-hour intervals up to

24 HOURS

3. Press

SELECT

softkey to save your selection. The indicator on the base will blink and a DND

timer will appear on the display indicating how much time remains before the DND feature is

automatically turned o.

4. To turn o DND feature at any time, press DND/PRIVACY.

8.9 Line Privacy

This feature will prevent other phones on the same system from accessing the line used by your

active call.

To turn on Line Privacy:

1. While on a call, press DND/PRIVACY.

2. The screen will display

PRIVACY

8.10 Flash

If you subscribe to Call Waiting Caller ID service from your local telephone company and you

receive an incoming call during a call, you will hear a beep to indicate another call is waiting on the

line and Caller ID information (if available) for the waiting call shows on the display.

1. To connect to the waiting call, press FLASH and your ﬁrst call will be put on hold.

2. To switch between the two calls, press FLASH.

8.11 Inserting a Pause in the Dialing Sequence

Press j twice to insert a delay in dialing sequence when a pause is needed to wait for a dial

tone (for example, after you dial 9 for an outside line, or to wait for a computer access tone). Each

pause counts as one digit in the dialing sequence, and is shown as

in the display.

8.12 Redial

1. Pick up the handset, press s or HEADSET and the base will select the ﬁrst available line. If

both lines are available, Line 1 will be used ﬁrst.

Or, press LINE 1 or LINE 2 button to select the line you want.

2. Press REDIAL. The redial number list (last 3 previously dialed numbers) is shown.

3. Using VOL + and VOL - of the navigation button to scroll to the number you want to redial.

4. Press

DIAL

softkey to dial the phone number.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Motorola ML25254 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info