Bedienungsanleitung MTD CubCadet serie 2000 (Seite 16 von 18) (Englisch)

507836

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Operating instructions for lawn tractors English



The rear axles must be lubricated

with a special-purpose (water-

repellent) grease at a specialised

garage.



Have the cutting blade sharpened

or replaced in a specialist

workshop.

Note

Regularly check (when visiting

your workshop) the condition

of the mower deck V-belt.

Installing/removing and

adjusting cutter deck

a~åÖÉê

oáëâ=çÑ=áåàìêó=Ñêçã=ÉåÖáåÉ=ëí~êíáåÖ=

ìåáåíÉåíáçå~ääó

mêçíÉÅí=óçìêëÉäÑ=Ñêçã=áåàìêóK=_ÉÑçêÉ=

ÇçáåÖ=~åó=ïçêâ=íç=íÜáë=~é éäá~åÅÉ W

Ó é~êâ=íÜÉ=~ééäá~åÅÉ=çå=~=äÉîÉä=

ëìêÑ~ÅÉI

Ó íìêå=íÜÉ=ÉåÖáåÉ=çÑÑI

Ó êÉãçîÉ=íÜÉ=áÖåáíáçå=âÉóI

Ó ëïáíÅÜ=çÑÑ=mqlI

Ó äçÅâ=íÜÉ=é~êâáåÖ=Äê~âÉI

Ó ï~áí=ìåíáä=~ää=ãçîáåÖ=é~êíë=Ü~îÉ=

ÅçãÉ=íç=êÉëí=~åÇ=íÜÉ=ÉåÖáåÉ=Ü~ë=

Ñìääó=ÅççäÉÇI

Ó êÉãçîÉ=íÜÉ=ëé~êâ=éäìÖ=ÅçååÉÅíçê=

çå=íÜÉ=ÉåÖáåÉ=áå=çêÇÉê=íç=éêÉîÉåí=

íÜÉ=ÉåÖáåÉ=Ñêçã=~ÅÅáÇÉåí~ääó=ÄÉáåÖ=

ëí~êíÉÇK

a~åÖÉê

oáëâ=çÑ=áåàìêó=Ñêçã=ëÜ~êé=ÅìííÉêëK

tÉ~ê=éêçíÉÅíáîÉ=ÖäçîÉ ëK

Assembly

Note

Work proceeds faster when you

are assisted by a second person.

Mounting the cutting

mechanism



Move the cutting height setting

lever into the top catch (HI/16).



For units with electric cutter deck

lifter: Move lever for setting the

height/depth to the lowest position

(LO/1) and press the switch

for the electric lifter backwards.



Push cutter deck from the right side

under the tractor.

Fig. 19



Align cutter deck so that the rear

cutter deck holders (1) are under

the locating holes (2) of the lifting

arms (3).



Lower lifting arms (3):

– Move cutting height adjustment

lever to the lowest notch (LO/1).

– For units with electric cutter

deck lifter: Press switch for

the electric lifter forwards.

Fig. 20



Pull out the J-handle (1) on the left

cutter deck holder (2). Lift the back

of the cutter deck slightly until you

can press the J-handle into the

locating hole of the lifting arm (3).

Ensure that it engages correctly.



Repeat this work step on the right

side of the cutter deck.

Fig. 21



Remove the two nuts from the

fixing bracket (1).



Attach fixing bracket (1) to the

holders (2) on the cutter deck.



Insert the ends of the fixing bracket

into the locating holes of the holder

(3) on the tractor.



Screw the two nuts back onto

the fixing bracket.

Note: Do not tighten the nuts yet.

Attaching the drive belt

Note

The “V” side of the drive belt must

be in the belt pulleys.

Fig. 22



Place drive belt (1) on the engine

coupling belt pulley (2) (PTO).



Feed drive belt downwards and

place on the two deflection belt

pulleys (3).

Note: On the right deflection belt

pulley the V-belt guide (4) must

be bent outwards slightly so that

the drive belt can be attached.

After attaching the drive belt, bend

V-belt guide back!



Feed drive belt backwards and

attach it to the cutter deck.

Fig. 23



Press belt pulley holder (1) on

the cutter deck backwards,

the belt pulley moves forwards.

Place the drive belt on the belt

pulley (1, Fig. 24). Slowly feed the

belt pulley holder back.

=oáëâ=çÑ=áåàìêóK

qÜÉ=ÄÉ äí= é ìääÉó=ÜçäÇÉê= áë=ìåÇÉê= ëíêçåÖ=

ëéêáåÖ=íÉåëáçå=Ó=ïçêâ=ïáíÜ=ÉñíêÉãÉ =

Å~ìíáçå>



Check that the drive belt is positio-

ned correctly on all belt pulleys.

Installing the spacer (stop

for the cutter deck lifter)

Fig. 25

Note

The spacer must be installed before

the cutter deck is set.



Using the screws (2), attach

the two holders (1) to the right and

left sides of the tractor frame.

Note

If the cutter deck has a cutting width of

107 cm, only one

spacer is attached

to the left

side of the tractor frame.

Removing the transport secu-

ring device at the ejector flap

Fig. 18

Depending on the model remove

the locking plate or cable tie.

The deflector closes automatically.

Setting the cutter level

t~êåáåÖ

^ÑíÉê=áåëí~ääáåÖ=íÜÉ=ÅìííÉê=ÇÉÅâI=

ëÉí=íÜÉ=ÅìííÉê=ÇÉÅâ=äÉîÉäK

Note

Before aligning the cutters check

the tyre pressure on the appliance.

Set the level from front to back.

Fig. 26



Move the cutter deck to a medium

height position.



Carefully turn the outer cutters

(risk of injury) parallel to the drive

direction.



Measure the distance between

the ground and the end of the right

cutter. The end of the front cutter

should be about 6–10 mm lower

than the end of the rear cutter.

You may have to adjust the front

receiver (1). Set the correct level

by adjusting the nuts (2) equally.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 2000 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info