Bedienungsanleitung MTD CubCadet serie 2000 (Seite 15 von 18) (Englisch)

507836

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

English Operating instructions for lawn tractors

Cutters with cleaning nozzle

(optional)

Fig. 16

Place the appliance on an even

surface free of debris, stones, etc.,

and engage the locking brake.

1.Use a commercially available

quick-release coupling to attach

a water hose. Turn on water.

2.Start the engine.

3.Lower the cutters, and switch ON

for a few minutes.

4.Switch OFF the cutters and

engine.

5.Detach the water hose.

Repeat steps 1 to 5 for the second

cleaning nozzle (if provided).

At the end of cleaning (steps 1 to 5):



Raise the cutters to the top,



start the engine, and switch ON

the cutters for a few minutes

to dry them.

Cleaning accessories



See instructions in the operating

manual for the accessories.

Servicing the vehicle

Observe the servicing guidelines

in the engine manual.

At the end of the grass-cutting

season, have the appliance checked

and serviced in a specialist workshop.

`~ìíáçå

båÖáåÉ=çáä=áë=Ü~ò~êÇçìë=

íç=íÜÉ=ÉåîáêçåãÉåí

m~ëë=çå=~åó=ï~ëíÉ=çáä=ïÜ áÅÜ=Åçã Éë=

~Äçìí=íÜêçìÖÜ=~å=çáä=ÅÜ~åÖÉ =

íç=~=ÅçääÉÅíáçå=éçáåí=çê=~= ï~ëíÉ=

Çáëéçë~ä=Åçãé~åóK

oáëâ=çÑ=éçääìíáçå=Ñêçã=Ä~ííÉêáÉë

rëÉÇ=Ä~ííÉêáÉë=Çç=åçí=ÄÉ äçåÖ=

íç=ÇçJãÉëíáÅ=êìÄÄáëÜK=

m~ëë=çå=ìëÉÇ=Ä~ííÉêáÉë=íç=~ =ÇÉ~ äÉê=

çê ~=ï~ëíÉ=Çáëéçë~ä=Åçãé ~åóK=

aáëã~åíäÉ=íÜÉ=Ä~ííÉêó=ÄÉÑçêÉ=

íÜÉ îÉÜáÅäÉ=áë=ëÅê~ééÉÇK

Using jump leads

a~åÖÉê

kÉîÉê=ÄêáÇÖÉ=~=ÇÉÑÉ ÅíáîÉ=çê=ÑêçòÉ å=

Ä~ííÉêó=ïáíÜ=àìãé=äÉ~ÇëK=

båëìêÉ=íÜ~í=íÜÉ=ìåáíë=~åÇ=íÜÉ=àìãé=

äÉ~Ç=Åäáéë=Çç=åçí=íç ìÅÜ =É~Å Ü=çíÜÉê=

~åÇ=íÜ~í=íÜÉ=áÖåáíáçåë=~êÉ=ëïáíÅÜÉÇ=çÑÑK



Connect the red jump lead to the

positive terminal (+) of the flat

battery and the donor battery.



Connect the black jump lead first

to the negative terminal (–) of the

donor battery. Connect the other

clip to the frame of the engine block

of the tractor with the flat battery

(as far away from the battery

as possible).

Note

If the donor battery is installed

in a vehicle, this vehicle must not

be started during the jump starting

process.



Start the tractor with the flat battery

and actuate the parking brake.



Disconnect the jump leads

in reverse sequence.

Tyre pressure

t~êåáåÖ

kÉîÉê=ÉñÅÉÉÇ=íÜÉ=ã~ñáãìã=éÉêãáíJ

íÉÇ=íóêÉ=éêÉëëìêÉ=Eë ÉÉ=ëáÇ É=ç Ñ íóêÉFK=

tÜÉå=éìãéáåÖ=ìé=íÜÉ=íóêÉëI=Çç= åçí=

ëí~åÇ=áå=Ñêçåí=çê=~ÄçîÉ=íÜÉ ãK

The recommended tyre operating

pressure is:

– front: 0.8 bar

– rear: 0.7 bar

Over-inflating reduces the longevity

of the tyres. Tyre pressure should

be checked before every journey.

After 5 operating hours



First engine oil change. See engine

manual for subsequent intervals.



Use the oil channel or (optional)

quick oil drain (Fig. 17).

After 10 operating hours



Lubricate all rotating and bearing

points of the accelerator pedal

and brake pedal with several

drops of light oil.



Clean battery terminals.



Change gear oil/gear oil filter

for the first time. This work should

be performed at a specialised

workshop.

Every 25 operating hours



Lubricate all cutter shafts, idlers,

and idler mounts with 251H EP

type grease applied to their

respective grease nipples.

This work should be performed

at a specialised workshop.



Lubricate the wheel bearings and

front wheel axes with 251H EP type

grease applied to their respective

grease nipples.



Lubricate wheels of the cutter

deck via the grease nipples using

a multi-purpose grease.



Lubricate steering shaft and stee-

ring housing via the grease nipples

using grease type 251H EP.

This work should be performed

at a specialised workshop.

Every 50 operating hours



Grass residue and other soiling

on the drive gears must be

removed at a specialised garage.



Change gear oil/gear oil filter.

This work should be performed

at a specialised workshop.

Every 2 months



For battery type 2 only – Fill battery

cells with distilled water up to 1 cm

beneath the filling aperture.

If necessary

Charging the battery

When the appliance is not used

for longer periods, we recommend

removing the battery from the appli-

ance and charging this before and

every two months during storage and

before the appliance is again put into

operation.

Note

Note the information in the operating

instructions for your battery charger.

Replace the fuse



Replace defect fuses only with

the equivalent rating.

Once a season



Apply multipurpose grease

to the teeth on the steering gear.



Lubricate the steering linkage

with a few drops of light oil.



Lubricate all moving parts and

bearing surfaces with a few drops

of oil (control levers, cutting height

adjustment).



Clean the spark plug and check

the gap between the electrodes

or replace the plug.

See engine handbook.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 2000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info