Bedienungsanleitung MTD CubCadet serie 2000 (Seite 13 von 18) (Englisch)

507836

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

English Operating instructions for lawn tractors

Preparing for operation



Park the appliance on a firm level

surface and lock the parking brake.



Conduct all work with the engine

switched off.



Remove the ignition key.

For all work on moving parts:



Open the bonnet and disconnect

the cable to the spark plug.

Set the driver seat

Fig. 7



Take your place on the driver seat.



Adjust the seat to the desired

position. Ensure that it engages

correctly!

Setting the steering wheel

Fig. 8



Take your place on the driver seat.



Move steering wheel to required

position. Ensure that it engages

correctly!

Setting the cutting mechanism

wheels (depending on model)

The cutter wheels should never

be lower than 6–12 mm above the

ground at the lowest cutter position.

The cutter wheels are not designed

to bear the loads generated by the

cutters and may have to be offset

accordingly.

Starting the engine



Sit in the driver seat.



Switch off cutter deck/accessories:

Switch off PTO and lift up cutter

deck.



Push the brake pedal down fully

or lock the parking brake.



Do not actuate accelerator pedal

(= N position).

Note

Units with hydrostatic drive are

in the “N” position when the acce-

lerator is not actuated.



Move the throttle to the middle

position (between and ).



To cold-start the engine, pull

the choke or move the accelerator

lever to .



Turn the ignition key to until the

engine is running (attempt to start

the engine for max. 5 seconds,

wait 10 seconds before attempting

to start the engine again).

When the engine is running,

set the ignition key to .



Slowly push back the choke.



Return the accelerator lever until

the engine runs smoothly.

Stopping the engine



Move the throttle to the middle

position.



Let the engine run for approx.

20 seconds.



Set ignition key to .



Remove the ignition key.



Engage the locking brake before

leaving the appliance.

Driving

a~åÖÉê

^Äêìéí=í~âÉçÑÑI=ëíçééáåÖ=ëìÇÇÉ åäóI=

~åÇ=ÇêáîáåÖ=~í=ÉñÅÉëëáîÉ=ëéÉÉÇë=ê~ áëÉ=

íÜÉ=êáëâ=çÑ=~ÅÅáÇÉåíë=~åÇ=Å ~å=Å~ ìëÉ=

Ç~ã~ÖÉ=íç=íÜÉ=ìåáíK=

kÉîÉê=ëÉíL~Çàìëí=íÜÉ=ÇêáîÉêÛë=ëÉ~í=

çê ëíÉÉêáåÖ=ïÜÉÉä=ïÜáä É=Ç êáîá åÖ K

Note

Be especially cautious when rever-

sing. Never change direction without

first stopping the appliance.



Start the engine as stated.



To ensure adequate power output,

move the throttle to .



Release the parking brake:

Press down fully the brake pedal,

and release it.



Slowly engage the drive pedal

until you have reached the speed

you want.

Stopping the appliance



Release the accelerator.



Press the brake pedal until

the appliance is stationary.

Mowing

Note

– In normal mowing mode

(see Operation, Ignition lock):

Before reversing, switch off and lift

up the cutter deck.

– In reverse mowing mode

(see Operation, Ignition lock):

Exercise particular care when

mowing in reverse and activate

only if absolutely essential.

– Do not change direction when

the appliance is coasting or driving.



Start the engine as stated.



To ensure adequate power output,

move the throttle to .



Switch on the cutter deck.



Lower the cutters.



Release the parking brake:

Press down fully the brake pedal,

and release it.



Slowly depress the forward drive

pedal for forward direction of travel

and speed. The appliance starts

moving.

General information

When adjusting the cutting height

and driving speed, ensure that

the machine is not overloaded.

Depending on the length, type, and

dampness of the grass it may become

necessary to adjust the cutting height

and appliance speed for the optimum

grass catcher performance.

If blockages occur, reduce the driving

speed and increase the cutting height.

The best way to mow

Cut the first two rounds so the cut

grass is thrown out sideways into

the middle.



Never allow the grass to grow

too long.



Never cut the grass too low.



Drive in a straight line.



Never mow at high speed, particu-

larly when a mulching kit or grass

catcher is installed.

Mulching

Various appliances can also mulch

when fitted with the corresponding

accessories. Ask your specialised

dealer for details.

Switching off the machine



Stopping the appliance:

Release the accelerator press

brake pedal until the appliance

is stationary.



Switch off the cutter deck/acces-

sories.



Move the throttle to the middle

position.



Raise the cutters to the top.



Set the ignition key to after

twenty seconds.



Engage the locking brake before

leaving the appliance.



Remove the ignition key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 2000 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info