Bedienungsanleitung MTD CubCadet serie 7000 (Seite 46 von 52) (Englisch)

629099

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

• Start the engine and allow it to run for a short

period. Stop the engine.

• Recheck the coolant level in the overflow

reservoir and refill as needed. Reinstall the

reservoir cap.

INSPECTION OF COOLING SYSTEM HOSES

Check the cooling system hoses and fan belt for

any cracks or deterioration after every 100 hours of

operation. Check for loose hose connections.

Replace any damaged hoses and tighten any loose

connections. Replace a worn or damaged fan belt.

CHANGING THE ENGINE COOLANT

The engine coolant should be drained and replaced

with new coolant solution yearly.

The dry capacity of the cooling system is

approximately 5.2 Liter. Dilute the antifreeze with

water at a 1:1 ratio to mix the coolant solution

(50 % antifreeze : 50 % water).

Change the engine coolant as follows:

• Drain the coolant when the engine is cold.

• Place the tractor on a level surface and raise the

tractor hood.

• Slide the overflow reservoir upward and off the res-

ervoir bracket to access the radiator drain plug.

• Locate the radiator drain plug in the lower

right

rear corner of the radiator. See Figure 56.

Figure 56

• Place a suitable container beneath the drain

plug and remove the cap from the overflow

reservoir.

• Turn the drain plug counterclockwise to re-

move. Allow as much of the old coolant as pos-

sible to drain from the system.

Coolant is a toxic substance. Dispose of in

an environmentally safe manner. Contact

your area EPA office for proper disposal

methods and recycling center locations.

• Reinstall the drain plug and turn clockwise until

fully tightened.

• Turn the radiator cap counterclockwise to the

first stop, then push downward on the cap and

turn counterclockwise to remove. Refer to

Figure 50.

• In stages, SLOWLY pour the coolant solution

into the filler neck, allowing as much air as

possible to escape through the neck. Fill to the

overflow flange of the filler neck.

• Wait a few minutes to allow air to escape

through the filler neck and refill as needed, then

reinstall the radiator cap.

• Fill the overflow reservoir to the "FULL" mark.

• Start the engine and allow it to run for a short

period. Stop the engine.

• Recheck the coolant level in the overflow

reservoir and refill as needed. Reinstall the

reservoir cap.

CHANGING THE AIR CLEANER

Check the air cleaner daily or before starting the

engine. Check for loose or damaged components

and check the condition of the filter element.

Remove any buildup of dirt and debris in the air

cleaner housing.

Replace the paper air cleaner element after every

300 hours of operation. More often if operating the

tractor under extremely dusty conditions.

Check and replace the air cleaner element as follows:

• Unlock the clamps to remove the air cleaner

housing cover. See Figure 57.

Figure 57

RESERVOIR

BRACKET

RADIATOR

DRAIN PLUG

COVER

CLAMP

Pull Outward

to Unlock

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 7000 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 7000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info