Bedienungsanleitung MTD Zero Turn Serie Frontcut (Seite 16 von 18) (Englisch)

495078

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Operating Instructions English

The recommended tyre operating

pressure is:

front: 0.7 bar

rear: 0.7 bar

Over-inflating reduces the longevity

of the tyres. Tyre pressure should be

checked before every journey.

After 5 operating hours

 First engine oil change. See engine

manual for subsequent intervals.

 Use the oil channel or (optional)

quick oil drain (Figure 18).

Every 10 operating hours

 Remove dirt and grass clippings

from under the V-belt cover of the

cutter deck (fig. 24).

 Lubricate all cutter shafts, idlers,

and idler mounts with 251HEP

type grease applied to their

respective grease nipples.

This work should be performed

at a specialised workshop

Every 25 operating hours

 Using a multi-purpose grease,

lubricate the front wheels on the

cutter deck frame via the grease

nipples (depending on model).

 Lubricating the steering

mechanism:

Fig. 19

– Lubricate wheel bearings and

axles of the rear wheels via the

grease nipples (2) with grease

type 251HEP*.

– Lubricate both steeting arms

(right and left) on the lubricating

nipples (1) with 251HEP*

grease.

* Use a commercially available

grease gun. According to the

model, a grease gun is enclosed.

Note

If the power needed increases when

steering, i.e. steering is made

difficult, grease earlier.

Every 50 operating hours

 Grass residue and other soiling on

the drive gears must be removed

at a specialised garage.

Every 2 months

 For battery type 2 only – Fill battery

cells with distilled water up to 1 cm

beneath the filling aperture.

If necessary

Servicing the battery.

 Always keep the battery clean.

 Avoid tipping the battery.

Battery acid may leak out!

 Grease battery poles with terminal

grease.

Charging the battery

When the appliance is not used for

longer periods, we recommend

removing the battery from the

appliance and charging this before

and every two months during

storage and before the appliance

is again put into operation.

Note

Note the information in the operating

instructions for your battery charger.

Replace the fuse

 Replace defect fuses only with the

equivalent rating.

Cleaning the steering gear

If spoadic steering difficulties or

a steering block is experienced

clean the steering gear mechanism

see “once a season”.

If that does not solve the problem,

visit a garage.

Once a season

 Cleaning the steering gear:

– Take away the cover

(3, Fig. 19).

– Clean the steering gear

cogwheels (right and left).

 Lubricate all moving parts and

bearing surfaces with a few drops

of oil (control levers, cutting height

adjustment).

 Clean the spark plug and check

the gap between the electrodes

or replace the plug. See engine

handbook.

 Have a repair shop lubricate the

wheel axles with special grease

(water-repellent).

 Have the cutting blade sharpened

or replaced in a specialist

workshop.

Setting the cutter deck

t~êåáåÖ

oáëâ=çÑ=áåàìêó=íÜêçìÖÜ=íÜÉ=ÉåÖáåÉ=

ÄÉáåÖ=ìåáåíÉåíáçå~ääó=ëí~êíÉÇK

mêçíÉÅí=óçìêëÉäÑ=Ñêçã=áåàìêóK=

_ÉÑçêÉ=~ää=ïçêâ=çå=íÜáë=ìåáí

Ó é~êâ=íÜÉ=~ééäá~åÅÉ=çå=~=äÉîÉä=

ëìêÑ~ÅÉ

Ó íìêå=íÜÉ=ÉåÖáåÉ=çÑÑI

Ó êÉãçîÉ=íÜÉ=áÖåáíáçå=âÉóI

ÓëïáíÅÜ=çÑÑ=mqlI

Ó äçÅâ=íÜÉ=é~êâ áåÖ=Äê~âÉI

Ó ï~áí=ìåíáä=~ää=ãçîáåÖ=é~êíë=Ü~îÉ=

ÅçãÉ=íç=êÉëí=~åÇ=íÜÉ=ÉåÖáåÉ=Ü~ë=

Ñìääó=ÅççäÉÇI

Ó êÉãçîÉ=íÜÉ=ëé~êâ=éäìÖ=ÅçååÉÅíçê=

çå=íÜÉ=ÉåÖáåÉ=áå=çêÇÉê=íç=éêÉîÉåí=

íÜÉ=ÉåÖáåÉ=Ñêçã=~ÅÅáÇÉåí~ääó=ÄÉáåÖ=

ëí~êíÉÇK

t~êåáåÖ

oáëâ=çÑ=áåàìêó=Ñêçã=ëÜ~êé=ÅìííáåÖ=

Ää~ÇÉ

tÉ~ê=éêçíÉÅíáîÉ=ÖäçîÉëK

When mowing does not appear to

be parallel to the lawn the cutters

can be aligned.

Note

Before aligning the cutters check the

tyre pressure on the appliance.

Setting the side level

Fig. 20

 Raise the cutters to the top

(medium height position)

 Carefully turn the outer cutters

(risk of injury) transverse to the

drive direction.

 Measure the distance between the

ground and the ends of the two

outer cutters. The result should

be the same.

If required, set the correct level by

adjusting the lifting cable (3, on left

or right). To do this, loosen the lock

nut (1) and set the correct level by

adjusting the nut (2). After setting

the level, retighten the lock nut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD Zero Turn Serie Frontcut Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD Zero Turn Serie Frontcut

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info