Bedienungsanleitung MTD Zero Turn Serie Z-Force SZ (Seite 10 von 18) (Englisch)

629101

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Operating Manual English

Fitting the steering column

Fig. 2b

Lower part (A) of the steering

column

 Press lower part (A) of the

steering column forwards out of

the transport position and attach

with the two supplied screws and

washers (1).

Upper part (B) of the steering

column

 Loosen clamping lever (2) anti-

clockwise.

 Tilt steering column (B) into the

required position.

 Tighten clamping lever (2)

clockwise to lock the steering

column in this position.

Installing the steering wheel

Fig. 2c

 Remove cover cap (1, depending

on model) from the steering

wheel. Remove screw (2) and

washer (3 ).

 When the wheels are straight,

place the steering wheel on the

steering shaft.

 Place on top the washer (3) with

the convex side up, and secure

the steering wheel with the

screw (2).

 Insert cover cap (1, depending

on model).

Installing the seat

Fig. 2d

Note

When attaching the seat, do not

damage the seat switch cable!

Push excess cable back into the

opening of the seat support.

Mounting discharge flap on

the cutter deck

Fig. 2e

 Remove screws (1) and nuts (2)

from the discharge opening (4)

of the cutter deck.

 Attach discharge flap (3) to the

discharge opening (4) using the

screws (1) and nuts (2).

Attaching trailer coupling

(optional)

Fig. 2f

 Remove trailer coupling (1) from

the rear panel (4) of the unit

by undoing the screws (2) and

nuts (3).

 Rotate trailer coupling (1)

horizontally by 180° and reattach

to the rear panel (4) of the unit

using the screws (2) and nuts (3).

Controls and indicators

Warning. Damage to the unit.

First of all the functions of the

controls and indicators are

described here. Do not execute any

functions yet!

Fig. 1

1 Forward pedal

2 Reverse pedal

3 Clamping lever for steering

column

4 Cutting height adjustment lever

5 Throttle/Choke *

6 Choke *

7 Combination indicator *

8 PTO switch

9 Ignition lock *

10 Fuel tap

11 Fuel tank

12 Tank contents display *

13 Gear release lever

14 Trailer coupling *

15 Can holder

16 Seat adjustment lever *

17 Steering wheel

18 Pedal for parking brake/

cruise control

19 Brake pedal

(* depending on model)

Forward pedal (1)

Fig. 12

The pedal controls the speed

in a forward direction.

Reverse pedal (2)

Fig. 12

The pedal controls the speed

in a reverse direction.

Information on forward/reverse

pedal

To stop or change direction of tra-

vel, release the appropriate pedal.

Clamping lever for steering

column (3)

Fig. 1

Is used to lock the adjustable

steering column.

Cutting height adjustment

lever (4)

Fig. 8

The cutting height adjustment lever

is used to adjust the height of the

cutter deck.

Transport position: Lever in the top

position “T” and engaged in this

position.

Removal/installation position of the

cutter deck: Fixing pin (2) in the

bottom position “ ” and cutting

height adjustment lever engaged

above on the fixing pin.

Mowing position: Insert fixing

pin (2) into the holes marked “1”

to “4” and cutting height adjustment

lever engaged above on the fixing

pin.

Notes

– After inserting the fixing pin, turn

it downwards to prevent it from

coming out of the fixing hole.

In the “mowing position” or

“removal/installation” position the

fixing pin must always be below

the cutting height adjustment

lever which must be correctly

engaged on the fixing pin.

– The “transport position” or

“removal/installation position”

must not be used for mowing,

otherwise the V-belt of the cutter

deck may be damaged.

 Press the button (1) on the

cutting height adjustment lever

and pull the lever all the way up

until it engages in the transport

position/“T”.

 Select cutting height by fixing the

pin (2) in a hole in the ratchet

plate.

Note

Each hole adjusts the cutter deck by

approx. 6.4 mm. The lowest cutting

height is approx. 3.2 cm and the

tallest cutting height is approx. 10 cm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD Zero Turn Serie Z-Force SZ Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD Zero Turn Serie Z-Force SZ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info