Bedienungsanleitung Multiplex COCKPIT SX (Seite 75 von 84) (Englisch)

561578

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Operating Instructions

Page 73

ENGLIS

Example: offset four-point swashplate

90° arrangement: Rotated

through 45°

You can set the COCKPIT SX to the arrangement shown

on the right if you are using swashplate type 4 and set

V-DREH to 45.

17. The free mixers MIX 1, 2 and 3

The COCKPIT SX features three free mixers. The mixers

are of equal value, and are set up and adjusted in the

same manner. All three mixers can also be used simul-

taneously.

In the EASY model type only MIX 1 is available. In the

model types GLIDER, ACRO and HELI you can work

with all three mixers if you wish.

How do the free mixers work?

A free mixer allows you to mix the control signal of one

transmitter control (source) into the control signal for a

servo (destination). The two control signals are simply

summed (added together). A switch can also be as-

signed to the mixer, so that the mixer input can be

switched on or off.

Two steps are required to prepare a free mixer:

a. Defining the mixer (17.1.)

Define the destination and the switch

b. Setting the mixer effect (Î 17.2)

Define the magnitude of the mixer input

17.1. Defining / adjusting the free mixers

Menu: (MIXER) MIXDEF

The MIXDEF menu is used to define the source, desti-

nation and switch for the free mixers.

Moving to the MIXDEF menu:

4 to MENU, r (SETUP appears),

3 to MIXER, r (TH >S4 appears),

3 to MIX1

r (MIXDEF appears)

If the MIXDEF menu does not appear, the mixer is

already defined, and can now be adjusted (Î 17.1.).

Press the 3-D digi-adjustor again briefly to open the

menu for defining the mixer.

Source Switch Target

In the right-hand picture AILERON is selected as the

source. The destination is servo 5. The mixer input is

switched on when switch 1 (CS/A-ROT) is in the for-

ward position.

a. Select the source

Move the stick / slider briefly

(Quick-Select)

The trims are not taken into account

b. Select the destination

Servo 1 to 7; use the 3-D digi-adjustor

c. Select the switch

Move the desired switch (Quick-Select);

The code number (1 to 4) appears

Move the switch to the

“mixer input active” position; the

hyphen indicates the selected setting

Code

No.

Switch name Function

A-ROT

Combi-Switch

Auto-rotation

D-R Dual Rate

SNAP

DTC

Snap Flap

Direct Throttle

AUX 2

Flight phases

Aux. channel AUX2

You can change the source, destination and switch in

any way, as long as you remain in this menu.

Once you have selected the source, destination and

switch, press the 3-D digi-adjustor r briefly to return to

the MIXDEF menu.

Note: removing the switch

If you have assigned a switch when defining the mixer,

the switch can be changed, but not removed.

If you wish the mixer to work constantly, you must not

assign a switch to it. The only means of removing the

switch is to erase the definition (Î 11.4.), and then re-

define the mixer without a switch.

17.2. Adjusting the mixer effect

If you wish to continue, and adjust the effect of the

mixer, turn the 3-D digi-adjustor one click to the left 4;

the menu shown below then appears.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex COCKPIT SX Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex COCKPIT SX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info