Bedienungsanleitung Multiplex PROFImc3010 (Seite 73 von 79) (Englisch)

30252

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

Move

to the

"COPY

MEMORY"

menu, then

MODE:EXPORT".

Activate the source

memory

using

the

key.

The display

should

look like this,

with the memory

number

Jlashing:

rf'lü['E

E:":FüFtT

rFFlt''1.

ut: FiEITH

Press

the

key, and the data

will

transferred.

Two further

points:

1. ll

you

should

wish to interrupt an

import, export,

copy or delete

process

atter

you

have started, simply

switch

the transmitter

off briefly.

The data

the

model

memories

will then be unchanged.

2. To ensure

that import/export

possible

between all

versions

of the transmitter,

this

unction

is only

possi-

ble

with memories

15 and

Mx.

The

FIXED

VALUE

virtual

"transmitter

control"

you

wish to operate a

servo with a stick

(or

function

switch),

you

do not

need to

"lose"

a transmttter

control

for the

purpose.

Assuming, that

is, that all

you

need

are

two fixed servo

positions.

Assign

first:

Move to the

ASSIGN/SERVO

with

@Z[!N.

Select

the servo

you

wish to use,

press

the

key, and

assign

it to the

FIXED VALUE

"transmitter

control".

When

you

assign

the

"genuine"

transmitter control,

FIXED

VALUE

will not

appear.

Set up

as tollows:

Move to the

ADJUST / SERVO

/ TRAVEL

+ REVERSE

with the sequence

@ Z Z,

and

select the

servo

which

you

have assrgned

FIXED VALUE.

Finally

press

and

set the servo

position

for the first switch

position.

In the

"SWITCH

SERVO"

you

now

have to

determine

which switch

is associated

with the fixed

vatue.

The servo

position

for the second

switch

position

determined

in the menu ADJUST/SERVO/CENTRE.

be able

to do this,

you

must

first

back by one

level with the

key, and activate

Centre adjustment

with

. Now

move the

physical

switch to the

other

end-point,

press

the

key, and set the desired

sec-

ond

position

for the

servo.

ll. Tho

reeeiYing

s1stem

Connecting

servos

and

batteries

The

receiver

is the

"heart"

the receiving

system.

Servos,

motor

controllers,

switch

modules and

MULTINAUT-p|uS

receiver

modules

are connected

directly

to it.

The

receiver battery

is connected

to the

receiver via a

"switch

harness"

(Fig.

60).

Fis.60

The receiver

servo output

sockets are

numbered

from

l to a

maximum

oJ 10, depending

on the

number of

servos

which can

be connected.

Each servo

output

corresoonds

one control

function.

For reasons

of space, certain

output sockets

on the

smaller

receivers are combined,

that two servos

can

be connected

to one socket.

This type

socket

marked,

for example,

"8/9".

Only one

servo can be

connected directly,

and

this is always

the

lower

number;

in this case channel

What

you

need both

functions?

In this case

you

need

an expansion

adapter

(Order

No.8 5060),

which con'

sists

of a

plug

and two sockets.

The

plug

is connected

to the

receiver socket;

the two servos

are connected

the

two sockets

on the adapter

(Fig.

61).

Fig.61

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex PROFImc3010 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex PROFImc3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info