Bedienungsanleitung Multiplex ROYALevo9 (Seite 8 von 58) (Englisch)

30282

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

ROYAL evo

Seite 8

7.3. Inside the transmitter

The rechargeable transmitter battery c is installed as

standard. It consists of 6 environmentally friendly high-

capacity AA-size NiMH cells (Nickel-Metal-Hydride). For

safety reasons the individual cells are spot-welded to

ensure constant contact, and the pack is protected by a

heat-shrink sleeve.

Use genuine MULTIPLEX batteries only!

Observe charging hints!

(Î 8.4.)

The transmitter battery is fitted with a special

thermo-fuse which protects the battery and -

above all - the transmitter from short-circuit, re-

verse polarity and excessive currents. The transmit-

ter itself does not feature a separate fuse, and for

this reason the battery may only be replaced by a

genuine MPX transmitter battery pack designed

exclusively for this transmitter

RF module d (Radio Frequency module). The RF mod-

ule is simply plugged into the main circuit board, and

can easily be changed if you wish to switch to a differ-

ent frequency band (Î 7.4.3.). Two different RF mod-

ules can be used in the ROYALevo:

HFM-4:

! A simple, low-cost RF module with plug-in crystals for

selecting the channel (transmission frequency).

!Use only genuine MULTIPLEX transmitter crystals!

! The optional “Channel-Check” power-on guard mod-

ule can be fitted at any time.

HFM-S:

! A modern synthesizer RF module which allows you to

select the channel (i.e. transmission frequency) by soft-

ware.

! An optional scanner with power-on guard can be fitted

at any time.

The TORX ® screwdriver e (size T6), which you will find

in a clip below the aerial well, close to the screen, is

used for tasks such as swivelling the stick units, and for

installing the auxiliary switches in wells “K” and “P”.

On the inside of the transmitter back panel there are

crystal holders for 3 spare crystals.

Don’t lever the crystals out! Slide them out!

7.4. Mechanical details

7.4.1. Opening and closing the transmitter case

Be sure to switch the transmitter OFF before

opening it (short-circuit hazard)!

Opening the transmitter case:

1. Hold the transmitter in both hands and push the

sliding latches on the back panel downwards with

your thumbs (towards “OPEN”) (Fig. 1).

Carefully lift off the back panel of the case (Fig. 2).

Fig 1:

Fig. 2:

Closing the case:

1. Carefully position the back panel on the rear edge

of the case, holding it at an angle as shown, and

check that both retainer lugs are correctly engaged

(arrow) (Fig. 3).

2. Carefully close the case back (Fig. 4).

! Check that no cables are snagged, and that the

transmitter aerial has not slipped out of its guide

sleeve. It should be possible to fit the case back eas-

ily and without forcing.

3. Push the sliding latches up as far as they will go, in

the opposite direction to “OPEN”.

Fig. 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo9 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info