Bedienungsanleitung Multiplex ROYALevo9 (Seite 9 von 58) (Englisch)

30282

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Instructions

Seite 9

ENGLISH

Fig. 4

7.4.2. Adjusting the transmitter aerial,

fitting a new aerial

The transmitter aerial is a permanent fitting in the case.

For transport it can be collapsed completely and re-

cessed into the case. For adjustments and programming

the aerial can be left in this position without damaging

the RF section.

When operating a model always extend the

aerial to its full length. Only in this configura-

tion can you be sure of safe operation with

maximum radiated power and range.

The aerial can also be moved to a second position (an-

gled up and to the left), and locked in that position:

1. Pull out the aerial until you feel a distinct resistance

(Fig. 1).

2. Pull the aerial another 3 to 5 mm to overcome the

resistance, pulling fairly hard, and swivel the aerial

up and to the left (Fig. 2). You will again feel resis-

tance at this point, but this time do not push past it.

3. Tilt the aerial as far as it will go, and it will latch in

the correct position..

To swivel it back, the aerial must first be unlocked again

as described under point 2.

Check regularly that the aerial is still making

good contact. Contact problems with telescopic

aerials cause adverse effects on radiated power,

and thereby reduce effective range. In such

situations reliable operation can no longer be

guaranteed. Intermittent contact or bent aeri-

als should be replaced at the earliest opportu-

nity, as should an aerial that has become loose

and sloppy through hard use.

If the aerial should be damaged, it can be replaced eas-

ily as follows: Remove the case back, and simply push it

back and out of the aerial guide sleeve (replacement

ROYALevo aerial: # 89 3002).

Fig.1:

Fig. 2:

7.4.3. Installing and removing the RF module

The two RF modules (HFM-4 and HFM-S) for the ROYA-

Levo are not fitted in protective cases. To avoid dama-

ging them:

x Don’t touch the circuit board and its components.

x Don’t exert any force on the circuit board.

x Protect RF modules from mechanical strain.

Don’t touch components on the circuit board.

Don’t change the settings of adjustable com-

ponents.

If settings have been changed mistakenly or com-

ponents are damaged, have the module checked

an realigned by the MULTIPLEX service.

Removing the RF module:

1. Switch off the transmitter!

2. Open the transmitter (Î 7.4.1.)

3. Lay the front face of the transmitter on a soft sur-

face, taking care to avoid damage to the sticks and

switches!

4. Grasp the RF module by all four corners using both

thumbs and index fingers, and carefully pull it up

and out (see picture below).

Replacing the RF module:

Grasp the RF module as before. Ensure that the module

is fitted onto the contact pins correctly, i.e. that it is not

offset in any direction.

When changing the RF module avoid touching

the electrical components at all costs. If the

module is to be stored outside the transmitter,

it is essential to protect it from dirt and damp,

and also from shock and vibration.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo9 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info