Bedienungsanleitung NAD C 356 BEE (Seite 5 von 18) (Englisch)

493506

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

INTRODUCTION

GETTING STARTED

UNPACKING AND SETUP

WHAT’S IN THE BOX

Packed with your C 356BEE you will nd:

• The SR 8 remote control with 2 (two) AA batteries

• This owner’s manual

• A detachable mains power cord

SAVE THE PACKAGING

Please save the box and all of the packaging in which your C 356BEE

arrived. Should you move or otherwise need to transport your C 356BEE,

this is by far the safest container in which to do so. We’ve seen too many

otherwise perfect components damaged in transit for lack of a proper

shipping carton, so please: Save that box!

CHOOSING A LOCATION

Choose a location that is well ventilated (with at least several inches to

both sides and behind), and that will provide a clear line of sight, within

23 feet/7 meters, between the C 356BEE’s front panel and your primary

listening/viewing position. This will ensure reliable infrared remote control

communications. The C 356BEE generates a modest amount of heat, but

nothing that should trouble adjacent components. It is perfectly possible to

stack the C 356BEE atop other components, but the reverse usually should

be avoided.

It is especially important that sucient ventilation be provided. If you are

contemplating locating the C 356BEE within a cabinet or other furniture,

consult your NAD audio/video specialist for advice on providing adequate

airow.

NOTES ON INSTALLATION

Your C 356BEE should be placed on a rm, level surface. Avoid placing the

unit in direct sunlight or near sources of heat and damp. Allow adequate

ventilation. Do not place the unit on a soft surface like a carpet. Do not

place it in an enclosed position such a bookcase or cabinet that may

impede the airow through the ventilation slots. Make sure the unit is

switched o before making any connections.

The RCA sockets on your C 356BEE are colour coded for convenience. Red

and white are Right and Left audio respectively. Use high quality leads and

sockets for optimum performance and reliability. Ensure that leads and

sockets are not damaged in any way and all sockets are rmly pushed home.

For best performance, use quality speaker leads of 16 gauge (1.5mm

)

thickness or more. Switch o the POWER switch if you intend not to use the

C356BEE for long periods of time (such as when on vacation).

Should water get into your C 356BEE, shut o the power to the unit and

disconnect the plug from the mains power source. Have the unit inspected

by a qualied service technician before attempting to use it again.

DO NOT REMOVE THE COVER; THERE ARE NO USERSERVICEABLE

PARTS INSIDE.

Use a dry soft cloth to clean the unit. Do not use solutions containing

benzol or other volatile agents.

BARE WIRES AND PIN CONNECTORS

WARNING: The terminals marked with this symbol

are hazardous live. External wiring connected to these

terminals requires installation by an instructed person or

the use of ready-made leads or cords.

Bare wires and pin connectors should be inserted into the hole in the shaft

of the terminal. Unscrew the speaker terminal’s plastic bushing until the

hole in the screw shaft is revealed. Insert the pin or bare cable end into

the hole and secure the cable by tightening down the terminal’s bushing.

Ensure bare wire from the speaker cables does not touch the back panel or

another socket. Ensure that there is only ½ inch (1cm) of bare cable or pin

and no loose strands of speaker wires.

QUICK START

In case you simply cannot wait to experience the performance of your new

C 356BEE, we provide the following “QUICK START” instructions to get you

underway.

Please make all the connections to your C 356BEE with the unit unplugged

from the mains power source. It is also advisable to power down or unplug

all associated components while making or breaking any signal or AC

power connections.

1 Connect your speakers to the LEFT and RIGHT speaker terminals and

input sources to the applicable rear panel input sockets.

2 Connect the mains power cord to the C 356BEE’s AC Mains input and

then plug into a mains power source.

3 Set the rear panel POWER switch to the “ON” setting. The Standby LED

indicator embedded around the bezel of the STANDBY button will

illuminate amber and the C 356BEE goes to standby mode.

4 Press the front panel STANDBY button to turn ON the C 356BEE. The

Standby LED indicator will turn from amber to blue.

5 Select preferred active Source input by pressing the corresponding

front panel input selector button.

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 356 BEE Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 356 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info