Bedienungsanleitung NAD C 356 BEE (Seite 6 von 18) (Englisch)

493506

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

IDENTIFICATION OF CONTROLS

FRONT PANEL

1 STANDBY BUTTON: With the rear panel POWER switch set to ON

position, press this button to switch ON the C 356BEE from standby

mode. The Standby LED indicator will turn from amber to blue. Pressing

the STANDBY button again turns the unit back to standby mode.

The C 356BEE can also be switched ON from standby mode by pressing

any of the front panel buttons.

AUTO STANDBY (FOR 230V VERSION MODEL ONLY)

Auto Standby feature is an integral feature of C 356BEE that conforms

to European ecodesign regulations. The C 356BEE can be setup

to automatically go to standby mode if there is no user interface

interaction and no active source input within 30 minutes. Auto standby

mode can be enabled or disabled by the following steps.

Enable Auto Standby mode

At operating mode, press and hold together STANDBY and MP buttons

until Standby LED ashes once.

Disable Auto Standby mode

At operating mode, press and hold together STANDBY and MP buttons

until Standby LED ashes twice.

2 STANDBY LED: This indicator will light up amber when the C 356BEE

is at standby mode. When the C 356BEE is powered up from standby

mode, this indicator will illuminate blue. When infrared command from

the SR 8 is received, this indicator will also ash momentarily.

In cases of serious abuse of the C 356BEE, such as excessively low

loudspeaker impedance and short circuit, the C 356BEE will engage its

Protection circuitry, indicated by the Standby LED turning from blue to

red and the sound being muted.

In such a case, turn OFF the C 356BEE via the rear panel POWER switch.

Wait for it to cool down and/or check the speaker connections. Once

the cause for the protection circuitry to engage has been removed, set

the rear panel POWER switch to the “ON” setting. Then press the front

panel STANDBY button to resume normal operation.

3 PHONES: A 1/4” stereo jack socket is supplied for headphone listening

and will work with conventional headphones of any impedance. The

headphone socket will work in parallel with the selected speakers. To

listen to headphones only, de-select SPEAKERS A and/or B. The volume,

tone and balance controls are operative for headphone listening. Use

a suitable adapter to connect headphones with other types of sockets,

such as 3.5mm “personal stereo” jack plugs.

NOTE

Make certain that the volume control is turned to minimum (fully

counterclockwise) before connecting or disconnecting headphones.

Listening at high levels can damage your hearing.

4 SOFT CLIPPING INDICATOR: This indicator is illuminated blue if the

rear panel SOFT CLIPPING switch is set to ON position. Refer also to the

item below about SOFT CLIPPING at the IDENTIFICATION OF CONTROLS

– REAR PANEL.

5 MP SOCKET: Using a 3.5mm stereo plug, connect into this socket the

audio output of a Media Player.

NOTES

• If an external Media Player is connected to the front MP socket (using a

3.5mm stereo plug) while listening to a MP line-level source, the external

Media Player will be directly selected with the MP line-level source

immediately disconnected.

• It is recommended to mute the volume or switch to a dierent input

before plugging/unplugging the external Media Player cable.

6 REMOTE SENSOR: Point the SR 8 remote control at the remote

sensor and press the buttons. Do not expose the remote sensor of the

C 356BEE to a strong light source such as direct sunlight or illumination.

If you do so, you may not be able to operate the C 356BEE with the

remote control.

Distance: About 23ft (7m) from the front of the remote sensor.

Angle: About 30° in each direction of the front of the remote sensor.

1211107 8 9

2 3 4 5 6

ENGLISH PORTUGUÊSFRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 356 BEE Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 356 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info