Bedienungsanleitung NAD C 388 Hybrid Digital DAC Amplifier (Seite 16 von 22) (Englisch)

667807

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

IR CHANNEL

The C 388 has the capability to operate via Alternate IR channel. This is

useful if you have two NAD products that can be operated by similar

remote control commands. With alternate IR Channel, two dierent NAD

products can be controlled independently in the same zone by setting

each one to a dierent IR channel.

IR Channel Assignment

The C 388 and the SR 9 remote control must be set to the same channel.

To change the IR Channel on the C 388

While at IR Channel menu, use the [a/s] to select through Channel 0 to

Channel 3. Press [ENTER] to select preferred IR Channel setting. C 388 IR

Channel is defaulted to Channel 0.

To change the IR Channel on the SR 9 remote control

• Include a channel number before the library code. For SR 9, library code

“10” is the default library table for “AMP” device. To select this “AMP”

library table for Channel 0, retain the library code “10” (or “010”).

• If you want to load the “AMP” library table on ”Channel 1” prex the

library code with “1” to indicate association with “Channel 1”. Load then

the “AMP” library table using the code “110”. Repeat the same for MP

(130) and TUNER (140).

SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE

NAD C 388 and NAD C 390DD are both defaulted to Channel 0. If [OFF]

button is pressed on the SR 9 remote control (or AVR 4 remote control for

the C 390DD), both products will go to standby mode. Press [ON] and both

products will power up from standby mode.

To prevent both products from simultaneously going in and out of standby

mode along with other common commands, set each one to a dierent

IR channel. In this setup, we will keep C 390DD and AVR 4 remote control

defaulted to “Channel 0”. As for C 388, we will assign it to “Channel 1”; the

same applies to SR 9.

Set C 388 and SR 9 to “Channel 1” via the following procedure.

C 388

While at “IR Channel” menu, use the [a/s] to go to “Channel 1” setting. Press

[ENTER] to select “Channel 1”.

SR 9

• Press and hold [AMP] in the DEVICE SELECTOR section of the SR 9.

• While holding down the device button [AMP], press “1”, “1” and “0” using

SR 9’s numeric buttons.

• Press [ENTER] while still holding down the device button [AMP]. The

AMP device selector will ash once to indicate that the library input is

successful.

With both C 388 and SR 9 set to “Channel 1”, the C 388 can now be

remotely controlled independent of the C 390DD.

NOTE

Performing a Factory Reset for C 388 or SR 9 will restore their respective

IR channel setting to “Channel 0”.

IR LEARNING DEVICE

IR Learning Device enables any non-NAD remote control to learn AMP

and BluOS basic remote control codes. With the learned codes, use the

congured non-NAD remote control to command or operate the C 388.

HOW TO LEARN REMOTE CONTROL CODES

1 Go to IR Learning Device menu. Select either AMP or BLS.

2 Select AMP and the rst Amp Learning Key appears – VOLUME UP.

3 Press ENTER to select VOLUME UP and initiate learning mode.

4 Direct or point the non-NAD remote control to the IR sensor in the

front panel. Then, press desired button on the non-NAD remote

control where VOLUME UP will be learned. Upon pressing the

designated button, display will turn to “Learned”.

5 “VOLUME UP” is now learned into the designated button. Repeat

the same for the other codes to be learned. The same procedure

applies for BLS learning.

OPERATION

USING THE C 388

IR Channel

SettingsSource Setup

Channel 0

Settings

IR Learning Device

SettingsSource Setup

AMP

Settings

Amp Learning Key

SettingsSource Setup

VOLUME UP

Settings

VOLUME UP

SettingsSource Setup

Learning...

Settings

VOLUME UP

SettingsSource Setup

Learned

Settings

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 388 Hybrid Digital DAC Amplifier Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 388 Hybrid Digital DAC Amplifier

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info