Bedienungsanleitung NAD C 390 DD (Seite 19 von 26) (Englisch)

493504

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

IR CHANNEL

IR Channel

}~CH0

`CH1

`CH2

The C 390DD has the capability to operate over four IR channel settings.

This is practically useful if you have several NAD products that can be

operated by similar remote control commands. With varying IR Channel

settings, dierent NAD products can be controlled independently in the

same zone by setting each one to a dierent IR channel.

IR CHANNEL ASSIGNMENT

The C 390DD and the AVR 4 remote control must be set to the same

channel.

To change the IR Channel on the C 390DD

• While at “IR Channel” menu, use the [D/F] to select through CH 0

to CH 3. Press [S] to select preferred IR Channel setting. C 390DD IR

Channel is defaulted to CH0.

To change the IR Channel on the AVR 4 remote control

• Include a channel number before the library code. For AVR 4, library

code “10” is the default library table for “AMP” device. To select this “AMP”

library table for IR Channel 0 (CH0), retain the library code “10” (or “010”).

• If you want to load the “AMP” library table on ”IR Channel 1” (CH1) prex

the library code with “1” to indicate association with “IR Channel 1” (CH1).

Load then the “AMP” library table using the code “110”. Repeat the same

for MP (130) and TUNER (140).

SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE

NAD C 390DD and NAD C 326BEE are both defaulted to IR Channel 0. If

[OFF] button is pressed on the AVR 4 remote control (or SR 8 remote control

for the C 326BEE), both products will go to standby mode. Press [ON] and

both products will power up from standby mode.

To prevent both products from simultaneously going in and out of standby

mode along with other common commands, set each one to a dierent

IR channel. In this setup, we will keep C 326BEE and SR 8 remote control

defaulted to “IR Channel 0” (CH0). As for C 390DD, we will assign it to

“IRChannel 1” (CH1); the same applies to AVR 4.

Set C 390DD and AVR 4 to “CH1” via the following procedure.

C 390DD

• While at “IR Channel” menu, use the [D/F] to go to “CH1” setting. Press

[S] or [ENTER] to select “CH1”. Press [A] to exit IR Channel selection.

AVR 4

• Press and hold [AMP] in the DEVICE SELECTOR section of the AVR 4.

• While holding down the device button [AMP], press “1”, “1” and “0” using

AVR 4’s numeric buttons.

• Press [ENTER] while still holding down the device button [AMP]. The

AMP device selector will ash once to indicate that the library input is

successful.

With both C 390DD and AVR 4 set to “CH1”, the C 326BEE can now be

remotely controlled independent of the C 390DD.

NOTE

Performing a Factory Reset for C 390DD or AVR 4 will result to a return to

the factory default “IR Channel 0” setting.

AUTO STANDBY

The C 390DD can be setup to automatically go to standby mode if there is

no active input in the current source for 30 minutes.

Auto Standby

}~On

`Off

On: C 390DD will automatically go to standby modeif there is no active

input in the current source for 30 minutes.

O: C 390DD will remain at operating mode even if there is no active input

in the current source for 30 minutes.

SOURCE SETUP

Source Setup

}Digital Coaxial 1

Digital Coaxial 2

Digital Optical 1

Source Setup makes it possible to select a Source and enable or disable it as

desired. The optional NAD DD AP-1 (Direct Digital Analog Phono) module

must be installed for “Single-ended” and “Balanced” sources to be functional.

The same applies for “Digital HDMI 1”, “Digital HDMI 2” and “Digital HDMI 3”

- the optional NAD DD HDM-1 (HDMI) module must also be installed. If the

applicable module is not installed, the corresponding sources will not be

available from the Source Setup menu selection.

OPERATION

USING THE C 390DD

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 390 DD Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 390 DD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info