Bedienungsanleitung NAD C 565 BEE (Seite 13 von 16) (Englisch)

493510

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

The CD 9 remote control is provided with your C 565BEE Compact Disc Player

to enable you to operate playback functions from the comfort of your chair or

from virtually anywhere in the room. For reliable operation, there should be a

clear line-of-sight path from the remote control to the front of the CD player. If

the player does not respond to remote commands, it may be that this line-of-

sight path is obstructed by clothing, paper or furnishings.

Most of the buttons on the remote control handset have the same eect as the

corresponding buttons on the front panel of the player. In addition, the handset

is equipped with some extra buttons like the following function keys.

NUMERIC KEY PAD

Using the direct-entry numeric keypad (0 to 9) causes the C 565BEE to jump

directly to the beginning of a numbered track and commence play. Thus, to

play Track 5, simply press “5”. To play Track 20, press “2” and “0”.

RPT A-B

To repeat a sequence, implement the following procedures:

1 Press [RPT A-B] at your chosen starting point. “REPEAT A B” is

illuminated in the VFD with “B” blinking.

2 Press [RPT A-B] again at your chosen end point. “REPEAT A B” stay

illuminated. The repeat sequence begins.

3 Press [RPT A-B] again to cancel the sequence.

DIM

Toggle to reduce, turn o and restore VFD brightness.

PROGRAM AND CLEAR

Use [PROG] button to start, review, edit or exit programming mode. In

combination with [PROG] button, the [CLEAR] button allows the deletion of

a programmed track during program review or edit sequence. Refer also to

the item about “PROGRAMMING” at the “USING THE C 565BEE – CD MODE”

section of the “OPERATION” page.

FILTER

The C 565BEE oers ve unique digital ltering options dedicated to the

achievement of a better audio experience. These selectable lters allow

users the exibility to choose key characteristics that aect frequency

response and time domain characteristics.

Before describing these ve digital lters, please take time to read the

following brief denitions of some of the terminologies used in their

descriptions.

• Passband is the range of frequencies or wavelengths that can pass

through a lter without being attenuated.

• A stopband lter rejects frequencies within a band and letting through

frequencies outside it.

• Group delay is the transit time of a signal through a device versus

frequency.

• Rollo is a term used to describe the steepness or slope of the lter

response in the transition region from the passband to the stopband.

• Ripple refers to uctuations in the passband or stopband of a lter’s

frequency magnitude response curve. It is the periodic oscillation in

the passband near the inection point of the lter (the point where the

passband meets the stopband).

The following is a brief description of each lter’s characteristics. The

selection of lter number is basically a matter of personal choice; tailor

the audio conversion by selecting the lter number that will best suit your

desired listening experience.

Filter 1: Slow roll o lter that has low group delay, low ripple and wide

stopband characteristics.

Filter 2: Medium roll o lter that has high group delay, low ripple and

medium stopband characteristics.

Filter 3: Fast roll o lter that has lower group delay and wider stopband

characteristics.

Filter 4: Medium roll o lter that has higher group delay and narrower

stopband characteristics.

Filter 5: Medium roll o lter that has lower group delay and wider

stopband characteristics.

NOTE

The lter eect applies only to the analog output; it is not applicable to

the digital outputs.

OPERATION

USING THE C 565BEE  CD 9 REMOTE CONTROL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 565 BEE Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 565 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info