Bedienungsanleitung NAD C 725 BEE (Seite 11 von 24) (Englisch)

493509

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

USING THE SR 8 REMOTE CONTROL

The SR 8 remote control handset handles the key functions of the C 725BEE as well as other NAD Stereo

Receivers, Integrated Ampliers and Preampliers. It has additional controls to remotely operate NAD CD

Players, AM/FM Tuners and dedicated AM/FM/DAB Tuners. It will operate up to a distance of 23ft (7m).

Alkaline batteries are recommended for maximum operating life. Two AAA batteries should be tted in the

battery compartment at the rear of the Remote Control handset. When replacing batteries, check that they

have been put in the right way round, as indicated on the base of the battery compartment.

When a command from the remote control is received, the Standby LED indicator will blink. Note that

the indicator may also blink when receiving commands not necessarily for the C 725BEE but for other

components in the system. Please refer to previous sections of the manual for a full description of

individual functions.

NOTE

The remote control handset supplied with the C 725BEE is of a universal NAD type, designed to

operate several NAD models. Some buttons are applicable only to specic NAD models. Contact

your dealer or NAD audio specialist for assistance.

1 POWER ON & OFF: The SR 8 remote has a separate ON and OFF button. Press the ON button

to switch the unit from Standby to operating mode. Press the OFF button to switch the unit to

Standby mode.

2 DEVICE SELECTOR: A Device Selector button determines only what component the SR 8 will

command; it does not perform any function on the receiver. Press desired Device Selector button

for the applicable buttons to be directed to a “page” of commands relevant to the selected device.

Upon selecting a Device, you can now press the corresponding SR 8 control buttons applicable for

the selected Device.

3 INPUT SELECTORS: Refer to the corresponding labels printed in the remote control faceplate

and their respective assigned buttons to make use of these functions. Set the DEVICE SELECTOR

to “AMP” in order to gain access to these buttons. The input selector buttons perform the same

functions as the buttons labeled the same on the front panel.

4 NUMERIC KEYS: The numeric keys allow for direct input of tracks for CD players, and direct

channel/preset access for tuners and receivers.

5 SLEEP: Switch o the NAD Receiver or Tuner after a preset number of minutes.

SLEEP MODE

The Sleep Mode timer will switch the C 725BEE to Standby mode automatically after a preset number of

minutes. Pressing the SR 8’s [SLEEP] button once will display the setting of the sleep time increment. Pressing

the SR 8’s [SLEEP] button a second time within a 3-second period will change the sleep time increment in

15-minute intervals, after which time the C 725BEE will automatically switch into Standby mode.

To adjust the sleep delay, press the SR 8’s [SLEEP] button twice; rst to display the sleep time

increment, and a second time to change the sleep time increment. The sleep time increment and a

“SLEEP” icon will continuously display on the C 725BEE’s front panel Vacuum Fluorescent Display (VFD).

Each consecutive press increases the sleep time in 15-minute increments from 15 to 90 minutes. To

cancel the sleep mode, continue pressing the SR 8’s [SLEEP] button until “Sleep O” displays on the

VFD. Switching the C 725BEE to standby from either the SR 8’s OFF or the C 725BEE’s Standby button

will also cancel the sleep mode.

6 MUTE: Press the [MUTE] button to temporarily switch OFF the sound to the speakers and

headphones. MUTE mode is indicated by the Standby LED indicator ashing for NAD Integrated

Ampliers or “Mute” shown in the VFD of NAD Receivers. Mute does not aect recordings made

using the TAPE or RECORD OUT/ZONE 2 outputs but will aect the signal going to the PRE OUT

outputs (if applicable). Press MUTE again to restore sound or by pressing [VOL ] of SR 8.

7 DIM (for use with NAD Stereo Receiver, Tuner and CD Player): Reduce, turn o or restore VFD

brightness. Depending on the NAD model, the brightness of the front panel display will vary when

you toggle this button.

IDENTIFICATION OF CONTROLS

REMOTE CONTROL

3, 4

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 725 BEE Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 725 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info