Bedienungsanleitung NAD C 725 BEE (Seite 9 von 24) (Englisch)

493509

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1 +12V TRIGGER OUT: The +12V TRIGGER OUT is used for controlling

external equipment that is equipped with a +12V trigger input. This output

will be 12V when the C 725BEE is ON and 0V when the unit is either OFF or

in standby. This output can drive a load up to 150mA at 12V.

2 IR IN/OUT: These mini-jacks accept and output remote-controlled

codes in electrical format, using industry-standard protocols, for use

with “IR-repeater” and multi-room systems and related technologies.

IR IN: This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the C 725BEE from a remote location.

IR OUT: When connected to the IR IN of an ancillary equipment, direct

the ancillary equipment’s own remote control to the C 725BEE’s infrared

receiver to command or control the linked unit.

All NAD products with IR IN/IR OUT features are fully compatible with

the C 725BEE. For non-NAD models, please check with your other

product’s service specialists as to their compatibility to the C 725BEE’s

IR features.

3 MP INPUT: Input for a Media Player or other line-level signal source.

Use a twin RCA-to-RCA lead to connect the Media Player’s left and right

“Audio Outputs” to this input. The MP input is also the assigned port

where the optional NAD IPD 1’s AUDIO OUT could be connected.

With the NAD IPD 1’s DATA PORT connected to the corresponding rear

panel’s DATA PORT socket, your iPod player docked in the NAD IPD

1 and the C 725BEE set to “MP” mode, you can start listening to your

iPod’s playlist. Refer also to LISTENING TO YOUR iPod PLAYER under the

OPERATION main heading.

4 CD INPUT: Input for a CD or other line-level signal source. Use a

twin RCA-to-RCA lead to connect the CD player’s left and right “Audio

Outputs” to this input.

5 DISC INPUT: Input for additional line level input signals such as CD,

Mini Disc player or the output signal from a step-up amplier for a

turntable. Use a twin RCA-to-RCA lead to connect the auxiliary unit’s left

and right “Audio Outputs” to this input.

6 AUX INPUT: Input for additional line level input signals such as

another CD player. Use a twin RCA-to-RCA lead to connect the auxiliary

unit’s left and right ‘Audio Outputs’ to this input.

7 TAPE: Connections for audio tape recorder playback of any type. Using

twin RCA-to-RCA leads, connect to the left and right “Audio Output” of

the tape machine to the TAPE sockets for playback.

8 REC OUT/ZONE 2: Doubles as both a RECORD and ZONE output port.

As a RECORD output, the Source signal directed to this output could

be used for making audio recordings. As a Zone output, it sends zone

selected audio sources to the corresponding audio input of another

separate zone. Use high quality patch cables to reduce noise pickup

over long distance runs.

9 PRE OUT: Connections to an external power amplier or processor,

such as a surround-sound decoder. In normal use, this should be

connected to the Main In sockets (No. 10) with the links supplied. To

connect your NAD C 725BEE to external processor or amplier sections,

remove rst these links. Use a twin RCA-to-RCA lead to connect the left

and right “Audio Input” of a power amplier or processor to the PRE OUT

sockets.

NOTE

Always turn the C 725BEE and associated external power ampliers OFF

before connecting or disconnecting anything to the PRE OUT and MAIN

IN sockets. The PRE OUT output signal will be aected by the C 725BEE’s

volume and tone control settings.

IDENTIFICATION OF CONTROLS

REAR PANEL

ATTENTION!

Please make sure that the C 725BEE is powered o or unplugged before making any connections. It is also advisable to power-down or unplug all

associated components while making or breaking any signal or AC power connections.

1 432 5 6 7 8 9 10 11 12 13 14

17 18 19 20 21

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 725 BEE Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 725 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info