Bedienungsanleitung NAD C 725 BEE (Seite 7 von 24) (Englisch)

493509

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1 STANDBY: With the rear panel POWER switch set to ON position, press this

button to switch ON the C 725BEE from standby mode. The Standby LED

indicator will turn from amber to blue and illuminate the VFD. Pressing the

[Standby] button again turns the unit back to standby mode.

The C 725BEE can also be switched ON from standby mode by pressing

any of the front panel buttons.

2 STANDBY LED: This indicator will light up amber when the C 725BEE

is in standby state. When the C 725BEE is at ON state, this indicator will

illuminate blue. When infrared command from the SR 8 is received, this

indicator will also ash momentarily.

In cases of serious abuse of the C 725BEE, such as excessively low

loudspeaker impedance and short circuit, the C 725BEE will engage its

Protection circuitry, indicated by the Standby LED turning from blue to

red and the sound being muted. At Protect mode, the Standby LED in

red color will ash and “Protect!” shown ashing also in the VFD. In the

case of overheating, the Standby LED in red color will ash and the VFD

turned o.

In such a case, turn the C 725BEE o by the rear panel POWER button,

wait for it to cool down and/or check the speaker connections,

making sure the overall loudspeaker impedance doesn’t go below 4

ohms. Once the cause for the protection circuitry to engage has been

removed, switch ON the rear POWER button and the Standby Button to

resume normal operation.

3 BLEND: The NAD BLEND feature will allow you to reduce the amount of

noise and hiss but still retain some level of stereo separation, instead of

mono. The BLEND button toggles between engaging and disengaging

the BLEND feature. When engaged, “Blend On” is shown at the lower line

of the VFD; “Blend O” when not active. The “Blend On” or “Blend O”

status can be stored for individual presets.

4 INFO: Toggle this button for the lower line of the VFD to show various

settings, conditions and other information relevant to the currently

tuned station or broadcast.

5 MEMORY: Press this button to store tuned AM, FM and digital radio

stations to the C 725BEE’s 40 preset-memory locations. One can store a

mix of any AM, FM and DAB broadcasts to the 40 available presets.

In combination with [INFO] button, [MEMORY] button is also used in

deleting stored presets. Press and hold [INFO] button and then press

[MEMORY] – current stored preset setting will be erased. Refer also to

the item about SETTING RADIO PRESETS at the LISTENING TO AM/FM

RADIO section of the OPERATION page.

6 TUNER MODE: In FM mode, toggle this button to switch between

“FM Mute On” (stereo) and “FM Mute O” (mono). Select “FM Mute O”

for stations that have too much interference or are too weak. When

engaged, “FM Mute On” is shown at the lower line of the VFD; “FM Mute

O” when not active. The “FM Mute On” or “FM Mute O” status can be

stored for individual presets. Refer also to the item about CHOOSING

TUNER MODE at the LISTENING TO AM/FM RADIO section of the

OPERATION page.

In DAB mode, pressing this button will activate Dynamic Range Control

(DRC), Station Order or other applicable DAB menu options. Refer also

to the item about DAB TUNER MODE at the LISTENING TO DAB RADIO

section of the OPERATION page.

7 PRESET [ ] : Press to step up or down between stored radio

presets; 40 presets are available. Note that this function “wraps”: Pressing

[PRESET ] will step from Preset 1 to Preset 40 or vice versa. “Unused”

presets are skipped over.

8 TUNE [ ] : Toggle either button to step up or down between

AM or FM frequencies. Press and release [TUNE ] to search up or

down - the C 725BEE will stop at the next suciently strong signal it

encounters. Note that this function “wraps” – that is, it will continue to

search from one end of the AM or FM band to the other until it stops

at a strong signal. Pressing [TUNE ] during the search process will

stop the search. Refer also to “OPERATION – LISTENING TO DAB RADIO”

for [TUNE ] usage in DAB operation.

9 VACUUM FLUORESCENT DISPLAY (VFD): Provide visual information

about the unit’s important modes, settings, functions, status of the

current source and other indicators. When in tuner mode, it displays

information about the current station or broadcast as supplied by the

service provider among other tuner settings.

IDENTIFICATION OF CONTROLS

FRONT PANEL

1 9

19181713 14 15 16

2 3 4 5 6 7 8 10 11 12

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 725 BEE Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 725 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info