Bedienungsanleitung NAD C 725 BEE (Seite 8 von 24) (Englisch)

493509

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

10 REMOTE SENSOR: Point the SR 8 remote control at the remote

sensor and press the buttons. Do not expose the remote sensor of the

C 725BEE to a strong light source such as direct sunlight or illumination.

If you do so, you may not be able to operate the C 725BEE with the

remote control.

Distance: About 23ft (7m) from the front of the remote sensor.

Angle: About 30o in each direction of the front of the remote sensor.

11 RECORD OUT/ZONE 2 SELECTOR: This knob doubles as both a record

and zone source selector. Rotate knob and select the Source you would

like to be directed out to REC OUT/ZONE 2 output port in the rear panel.

The directed Source signal at the REC OUT/ZONE 2 output port could

be used for making audio recordings or as an audio input to a separate

zone in your home.

ABOUT ZONE FEATURE

The Zone feature allows one to simultaneously listen to another active

Source of the C 725BEE that is dierent from the currently selected Source.

For example, while the C 725BEE is at CD mode, you can set the RECORD

OUT/ZONE 2 SELECTOR knob to “TUNER” and the active tuned station’s

audio will be directed to REC OUT/ZONE 2 output port in the rear panel.

You can then feed the REC OUT/ZONE 2 jack to another amplier or receiver

that is located maybe in another area of your home or building. With your

separate amplier or receiver selecting the fed signal and with speakers

connected, you can then enjoy listening to the tuned station. You can

vary the level of the tuned station by adjusting the Volume control of the

separate amplier or receiver. Refer also to the item USING THE

ZR 5 REMOTE CONTROL at the REMOTE CONTROL section of the

the IDENTIFICATION OF CONTROLS page.

12 VOLUME: The VOLUME control adjusts the overall loudness of the signals

being fed to the loudspeakers or headphones. Turn clockwise to increase

the volume setting; counter clockwise to lower it. The VOLUME control does

not aect recordings made using the REC OUT/ZONE 2 output but will

aect the signal going to the Pre-amp output (PRE OUT).

NOTE

If the Volume level is adjusted using the SR 8’s [VOL ] buttons, the

lower line of the VFD will show “Volume Up” when level is increased or

“Volume Down” if level is decreased.

13 PHONES: A 1/4” stereo jack socket is supplied for headphone listening

and will work with conventional headphones of any impedance. The

headphone socket will work in parallel to the selected speakers. To

listen to headphones only, de-select Speakers A and/or B. The volume,

tone and balance controls are operative for headphone listening. Use

a suitable adapter to connect headphones with other types of sockets,

such as 3.5mm “personal stereo” jack plugs.

NOTE

Make certain that the volume control is turned to minimum (fully

counter-clockwise) before connecting or disconnecting headphones.

Listening at high levels can damage your hearing.

14 A SPEAKERS B: The SPEAKERS A and B buttons engage or disengage

the speakers connected respectively to the SPEAKERS A and SPEAKERS

B terminals on the rear panel. Press “A” to switch ON or OFF the speakers

connected to the SPEAKERS A terminals. Press “B” to switch ON or OFF

the speakers connected to the SPEAKERS B terminals.

15 MP SOCKET: Using a 3.5mm stereo plug, connect into this socket the

audio output of a Media Player. The LED on the MP input button will

illuminate when an external Media Player is connected to this socket.

16 INPUT SELECTORS: These buttons select the active input to the NAD

C 725BEE and the signal sent to the loudspeakers, headphones and the

PRE OUT socket. The buttons on the remote control handset duplicate

these buttons. The selected input will be displayed in the VFD.

MP (MEDIA PLAYER): Selects a line-level source connected to the MP

sockets as the active input. If the DATA port of the optional NAD IPD 1

Dock with iPod (NAD IPD 1) is connected to the corresponding DATA

PORT in the rear panel, your iPod player docked and with the NAD IPD

1’s AUDIO OUT also connected to the rear panel MP input, the lower

line of the VFD will show “iPod Connected”. Refer also to LISTENING TO

YOUR iPod PLAYER under the OPERATION main heading.

If an external Media Player is connected to the front MP socket (using

a 3.5mm stereo plug) while listening to a MP line-level source, the

external Media Player will be directly selected with the MP line-level

source immediately disconnected. It is recommended to mute the

volume or switch to a dierent input before plugging/unplugging the

external Media Player cable.

CD: Selects the CD (or other line-level source) connected to the CD

sockets as the active input.

TUNER: Toggle to select AM, FM or DAB (230V version only) tuner band.

DISC: Selects a line-level source connected to the DISC sockets as the

active input.

AUX: Selects a line-level source connected to the AUX sockets as the

active input.

TAPE: Selects the Tape (or other line-level source) connected to the

TAPE sockets as the active input.

17 TONE DEFEAT: Tone Controls are enabled or disabled by pressing this

button. The lower line of the VFD will show “Tone Defeat” when the tone

controls are bypassed or “Tone Active” if the tone controls are enabled.

18 TONE CONTROLS: The NAD C 725BEE is tted with BASS and TREBLE

tone controls to adjust the tonal balance of your system. The 12 o’clock

position is “at” with no boost or cut, and an indent indicates this

position. Rotate the control clockwise to increase the amount of Bass or

Treble. Rotate the control counterclockwise to decrease the amount of

Bass or Treble. The Tone controls do not aect recordings made using

the REC OUT/ZONE 2 output but will aect the signal going to the Pre-

amp output (PRE OUT).

19 BALANCE: The BALANCE control adjusts the relative levels of the left

and right speakers. The 12 o’clock position provides equal level to the

left and right channels. A detent indicates this position. Rotating the

control clockwise moves the balance towards the right. Rotating the

control counterclockwise moves the balance to the left. The BALANCE

control does not aect recordings made using the REC OUT/ZONE

2 output but will aect the signal going to the Pre-amp output (PRE

OUT).

IDENTIFICATION OF CONTROLS

FRONT PANEL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

NAD C 725 BEE Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 725 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info