Bedienungsanleitung NAD C 725 BEE (Seite 14 von 24) (Englisch)

493509

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

The C 725BEE’s internal AM/FM tuner oers very high quality sound

from radio broadcasts. The reception and sound quality will always be

dependent to a degree however on the type of antenna(s) used as well as

proximity to the broadcast origin, geography and weather conditions.

ABOUT ANTENNAS

The supplied ribbon-wire FM antenna can be connected to the rear-panel

FM-antenna input using the included “balun” adapter and should be fully

extended to form a “T”. This folded-dipole antenna will usually work best

when oriented vertically, with the arms of its “T” fully outstretched and

arranged perpendicular to the origin of the desired broadcast. There are

no “rules” however, and experimenting freely with antenna placement and

orientation may yield the clearest sound and lowest background noise.

In areas of poor FM reception, an exterior FM antenna can improve

performance dramatically. If radio listening is important to you, consider

consulting an antenna installation professional to optimize your system.

The supplied AM “loop” antenna will usually provide adequate reception.

However, an exterior AM antenna can be used to improve reception.

Consult an antenna professional for more information.

ASSEMBLING THE LOOP ANTENNA

1 Rotate the outer frame of the antenna.

2 Insert the bottom edge of the outer frame into the groove on the stand.

3 Extend the antenna cord.

SELECTING BAND

Press the [TUNER] button on the front panel or on the remote control. Each

subsequent press of either key will toggle the unit among AM, FM and

DAB radio.

IMPORTANT NOTICE

In the foregoing sections about TUNER features, make sure to

set SR 8’s DEVICE SELECTOR to “TUN” for the applicable TUNER

commands to be eected.

TUNING STATIONS

1 Toggle [TUNE ] on the front panel or remote control to step up or

down between AM or FM frequencies.

2 Press and release [TUNE ] to search up or down - the C 725BEE’s

tuner will stop at the next suciently strong signal it encounters.

Pressing the [TUNE ] during the search process will stop the

search.

DIRECT TUNING

If you know your desired station’s frequency allocation, you can tune

directly to the station.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Tune” mode.

2 Using the numeric keys of the remote control, key-in the frequency

allocation of the station and then press [ENTER]. For example, to enter

104.50 MHz, press “1”, “0”, “4”, “5” and “0” or press “1”, “0”, “4”, “5” and [ENTER].

SETTING RADIO PRESETS AM/FM/DAB

The C 725BEE can store a mix of your 40 favorite AM, FM and DAB

broadcasts for immediate recall.

1 To store a radio preset, rst tune the desired frequency (see above), then

press the front panel [MEMORY] button. The VFD will show a blinking

“MEMORY” icon and the next available vacant Preset number – for

example, “Preset _ _Free” (the two blank spaces will correspond to the

preset number that could be from ‘01’ to the maximum of ‘40’).

2 Press [MEMORY] button again to store the desired frequency on the

Preset number shown or use the [PRESET ] keys to select another

available Preset number.

3 Then, press [MEMORY] key button again. Your desired frequency is now

stored in the assigned preset.

The Radio Presets can be stored using the same keys on the front panel or

remote control.

RECALLING PRESETS

1 Use the [PRESET ] keys on the front panel to step up or down

between presets.

2 Press and hold [PRESET ] to “scroll” continuously up or down.

3 Stop or release the [PRESET ] key while scrolling to select a desired

Preset number – the stored station will be recalled after a brief delay;

or press [ENTER] to tune immediately to the selected Preset number.

Empty presets will be skipped during preset tuning.

The SR 8 remote’s [PRESET ] keys work similarly.

DIRECT RECALL OF A PRESET

You can directly recall a desired Preset number.

1 Toggle SR 8 remote’s [ENTER] button to switch between “Preset” and

“Tune” mode (see the lower line of the VFD). Select “Preset” mode.

2 Using the numeric keys of the remote control, key-in directly your

desired Preset number and then, press [ENTER]. For example, to enter

Preset 5, press “5” and then, press [ENTER].

DELETE A PRESET

You can empty a preset by deleting the stored information.

1 Select the Preset number to be deleted.

2 Press and hold [INFO] button and then press [MEMORY] button

– current stored preset setting will be erased.

OPERATION

LISTENING TO AM/FM RADIO

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 725 BEE Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 725 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info