Bedienungsanleitung NAD C 725 BEE (Seite 16 von 24) (Englisch)

493509

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ABOUT DAB RADIO 230V VERSION ONLY

Until now, analogue radio signals such as FM or AM have been subject to

numerous kinds of interference on their way from the transmitter to your

radio. These problems were caused by mountains, high-rise buildings

and weather conditions. With Digital Audio Broadcast (DAB), you can now

receive CD-like quality radio programs without any annoying interference

and signal distortion. DAB broadcasts use digital signals rather than

traditional analogue transmissions, thus providing clear high quality

reception. You get far more robust reception and virtually hiss or crackle

free sound with DAB as long as you are within a good coverage area.

With DAB, the listener can scroll through a list of available stations - then

instantly tune to the station of his choice. There is no need either to

remember channel frequencies. All broadcasts are selected by simply

selecting the service name.

The C 725BEE makes it possible for you to enjoy listening to DAB broadcasts.

The C 725BEE has a Digital Audio Broadcast (DAB) module socket on the

rear panel for adding a separately sold and NAD-specied outboard DAB

module – the NAD DAB Adaptor DB 1. All the control software for this

format is included; just plug-in the module and start enjoying the CD-like

quality sound and expansive content selection available with DAB.

CONNECTING THE DAB MODULE

Plug-in the other end of the DIN connector (supplied with your NAD DAB

Adaptor DB 1) from the DAB module’s output port into the corresponding

DAB module input socket on the rear panel of the C 725BEE. Select DAB

mode on the C 725BEE by toggling the [TUNER] button in the front panel

or SR 8’s [TUN] button.

NOTES

• Please refer to NAD DAB Adaptor DB 1 installation guide for proper setup

connection of the DB1 with respect to the C 725BEE.

• If there is no NAD DAB Adaptor DB 1 connected, the VFD will show

“Check DAB Tuner”.

DAB OPERATION

With the separately sold NAD DAB Adaptor DB1 already connected to the

C 725BEE, you can now carry out the C 725BEE to receive DAB broadcasts.

1 Toggle [TUNER] button until DAB mode. The VFD will show “No Service

List” indicating that there are no scanned DAB broadcast services yet.

This is the default mode of the DB1.

2 To tune to DAB broadcast services, press [TUNER MODE] and then toggle

the front panel’s [TUNE ] to select either “Full Scan” or “Local Scan”.

FULL SCAN will enable the scanning of the full range of digital

frequencies (Band III and L-Band).

LOCAL SCAN performs local scanning of available DAB services in your

area. Check with your dealer or visit www.WorldDAB.org to check the

applicable digital transmission frequencies in your area.

3 Upon selecting either “Full Scan” or “Local Scan”, press SR 8’s [ENTER] button.

Automatic scanning will ensue. This sequence cannot be interrupted.

During the sequence, the following message will be visible in the VFD.

The bars show the progress of the sequence. When scanning is

completed, the last number shown on the right side of the VFD

corresponds to the total number of DAB broadcast stations found. Then,

the rst station is tuned in (See “ALPHANUMERIC” section below to

understand the order or arrangement of stations).

4 Press and hold SR 8’s [ENTER] button - the signal strength of the

currently tuned broadcast will be shown on the VFD. The more

segments visible in the lower display line, the stronger the signal. By

changing the position of the antenna, you can increase the signal

strength. You can also opt for an external antenna. Consult an antenna

professional for more information. Press SR 8’s [ENTER] button to exit

Signal Strength check.

NOTES

• “No Service List” will also be shown in the VFD when no stations are

found after the scanning process. If this occurs, check the connection

and position of the DAB antenna or call your local DAB broadcast

providers for coverage information.

• SR 8’s [TUNER MODE] and [ ] are the equivalent remote control

keys for the front panel buttons [TUNER MODE] and [TUNE ].

When using these SR 8 buttons to navigate DAB options, ensure that the

“DEVICE SELECTOR” setting of your SR 8 is set to “TUN”.

• Front panel’s [TUNER MODE] button also functions like SR 8’s [ENTER]

button. However, it is solely SR 8’s [ENTER] button that can check a DAB

station’s signal strength (item 4 above) or directly select a DAB station

after releasing [TUNE ] button (item 2 under “SERVICE LIST”); front

panel’s [TUNER MODE] button cannot execute these said functions.

SERVICE LIST

Follow the steps below to select through the DAB service stations found.

1 At DAB mode, press [TUNE ] to step through the list of available

stations as shown in the lower display line of the VFD.

2 Release [TUNE ] when you arrive at your desired DAB station and

the C 725BEE will tune to it. You can also press SR 8’s [ENTER] button

after releasing [TUNE ] for faster station selection.

DAB TUNER MODE

Aside from “Full Scan” and “Local Scan” as already described above, pressing

the [TUNER MODE] button will also present you with other options namely

– Station Order, DRC, Manual Scan, Prune List and Reset

OPERATION

LISTENING TO DAB RADIO

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

NAD C 725 BEE Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 725 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info