Bedienungsanleitung NAD M12 (Seite 15 von 22) (Englisch)

745048

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

The NAD HTRM 2 is ready to operate the M12 right out of the box, but it is really eight remotes in one.

Each of the 8 Device Selector keys at the top of the handset can call up a new “page” of remote control

codes to be transmitted by the remaining keys. You may “teach” codes from any infrared-remote

controlled component, regardless of brand, to any or all of these.

Obviously, the most logical system is that you teach the codes from your BD player to the [BD] Device

Selector “page,” your television’s codes to the [TV] “page,” and so on, but there is no required scheme:

You may load any commands to any key on any page (see “Learning Codes From Other Remotes,”

below).

The HTRM 2 is already preprogrammed with a full complement of commands for the M12 on its

[AMP] Device Selector page, and as well as with library commands to operate most NAD-brand CD,

BD or DAC components on the corresponding Device Selector “pages.” These default commands are

permanent: Even if you teach the HTRM 2 new commands to take their place, the underlying library

commands remain in place and can easily be recalled should you add an NAD component to your

system later (see “Delete Mode”, below).

Note: For use with the M12, it should not be necessary to re-program any keys on the HTRM 2 [AMP]

page. However, in order for the HTRM 2 to control your specic NAD-brand components you may

need to load one or more dierent code-libraries (see “Loading Code Libraries,” below).

CONTROLLING THE M12

The HTRM 2 is divided into two main sections. Eight Device Selector keys at the top—[AMP], [MP,]

[TV,] and so on—set the handset’s remaining keys to a “page” of commands to control a particular

component. A Device Select key determines only what component the HTRM 2 will command; it

does not perform any function on the M12. All of the remaining keys are function keys that can “learn”

control codes from virtually any infrared remote controller, allowing you to teach the codes of your

equipment, regardless of brand, to the HTRM 2.

However, the HTRM 2 is already preprogrammed to operate the M12. All of the function keys on the

[AMP] Device Selector “page” perform M12 functions. (The HTRM 2 can also command many other

NAD components, from its [CD], [BD], [DAC] and [CUSTOM] pages.)

It is important to note that certain HTRM 2 keys perform dierent functions depending on the selected

Device Selector “page.”

OPERATION

USING THE HTRM 2 REMOTE CONTROL

HTRM 2

OFF

SOURCE

SSEETTUUPP DDEELLAAYY // PPIICCTTUURREE TTEESSTT // ZZOOOOMM

EEQQ TTOONNEE LL..NNIITTEE

DDIIMMMMEERR

CHANNEL VOLUME

MMUUTTEE

PPRROOGGRRAAMM CCLLEEAARR RREEPPEEAATT

DAC

DEVICE SELECTOR

SSLLEEEEPP

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M12 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info