Bedienungsanleitung NAD M12 (Seite 17 von 22) (Englisch)

745048

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Example: Record a Macro to the [0] key to Turn on the M12, Select “Input1”

(Source 1), and Commence Playback of connected Source 1 device (as in

BD player):

• On the HTRM 2, simultaneously press-and-hold [MACRO] and

[0]



(numeric zero); the Learn LED turns steady green.

• Press [AMP]; press [ON]; press [1] (“Input or Source 1”); press [BD];

press



[4] (Play) - the Learn LED blinks as each step is added.

• Press [MACRO] again to exit the macro-record mode.

To clear a macro, perform the above steps without entering any functions.

EXECUTING MACROS

To execute a macro, press and release [MACRO]; its key illumination lights

for 5 seconds. While it remains lit, press an HTRM 2 key to which a macro

has previously been stored.

The corresponding macro will run; as each step executes, its “parent” Device

Selector’s key ashes lights briey; when execution is nished, the [MACRO]

key illumination goes out. Pressing any other HTRM 2 key while a macro is

executing will abort the macro. Remember that you must hold the HTRM 2

so that its infrared emitter can activate the target components.

NOTE

When a macro executes, a 1 second delay is automatically inserted

between its commands. If you need more than a 1 second delay between

particular commands—for example, to permit a component to power

up completely—you can record “empty” steps into the macro by

changing Device Selector “pages” without entering actual command

functions.

KEY ILLUMINATION TIMEOUT

The HTRM 2’s key-illumination can be set to remain lit for 0-9 seconds. The

default value is 2 seconds. To set the illumination timeout, simultaneously

press-and-hold for 3 seconds both the HTRM 2’s [DISP] and the [0-9] key,

with the digit corresponding to the desired timeout duration; the Learn

LED will ash twice to conrm the new setting. When set to zero, the

illumination will not turn on at all.

NOTES

• Key illumination is activated when one presses any HTRM 2 key.

• If HTRM 2 senses movement, key illumination is activated without

having to press a key. If HTRM 2 is shaken, key illumination is also

activated.

• Key illumination is the biggest drain on the HTRM 2’s batteries. A short

key illumination timeout will extend battery life appreciably; turning it

o altogether (set it to 0 seconds) will lengthen it still further.

CONFIGURING KEY ILLUMINATION

Keys to Press (for 3 seconds) Mode

DISP + Digit Key (0-9) Set key illumination timeout to number of

seconds corresponding to digit key. Zero turns o

the key illumination entirely.

DISP + OFF Disable light sensor. Key illumination will turn on

with any key press.

DISP + ON Enable light sensor.

DISP + ENTER Set the light sensor threshold to the current

light level.

DISP + RTN Restore all key illumination settings to the

defaults.

FACTORY RESET

The HTRM 2 can be reset to its factory state, deleting all learned commands,

copied and punched-through keys, macros, and other setup information,

reverting all keys to their pre-programmed library commands.

To perform a factory reset simultaneously press-and-hold for 10 seconds

the HTRM 2’s [ON] and [RTN] keys; the Learn LED will start to ash green.

Release [ON] and [RTN] before the second ash is complete; the Learn LED

will turn red, indicating the remote has been reset.

NOTE

You must release [ON] and [RTN] before the second ash goes out,

otherwise the unit will not reset; should this occur, repeat the full

procedure.

DELETE MODE

The HTRM 2 can store learned, copied, and “default library” commands on

any single key (The default library commands are the pre-programmed

NAD codes, such as the native M12 commands on the [AMP] “page.”).

You can delete commands by layers back “down” to the default library

command on any key, removing learned commands, punched-through

functions, and copied keys.

NOTE

The default library commands cannot be deleted, so you need not worry

that using Delete Mode might cause irreparable changes.

To enter Delete Mode, simultaneously press-and-hold for 3 seconds both

the desired key’s Device Selector key and the [RTN] key, until the Learn LED

turns green. Press the function key whose command you wish to delete;

the Learn LED ashes; the number of times indicates which type of function

has become active - see the table below. Press the active Device Selector

key again to exit Delete Mode.

NOTE

You may delete multiple function-key commands on the same Device

Selector “page,” but to delete from more than one Device Selector page

you must exit Delete Mode and then re-enter it on the required page.

Flashes Command Type

1 Default Library Command

2 Copied Library Command

3 Learned Command

OPERATION

USING THE HTRM 2 REMOTE CONTROL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M12 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info