Bedienungsanleitung NAD M15 HD2 (Seite 10 von 45) (Englisch)

745041

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

4 AUDIO PRE-OUT

The AUDIO PRE- OUT makes it possible to use the M15 HD as a pre-

amplier to external power ampliers for some or all channels.

• Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL and

SURR-BR to the respective channel input of a power amplier or

ampliers driving the corresponding applicable speakers.

• Connect the SUBW1 (and/or SUBW2) output to powered (“active”)

subwoofers or to power amplier channels driving a passive system.

• Unlike the full range channels, there is no power amplier built-into

the M15 HD for a subwoofer.

5 RS 232

NAD is a certied partner of AMX and Crestron and fully supports

these external devices. Check out the NAD website for information

about AMX and Crestron compatibility with NAD. See your NAD audio

specialist for more information.

• Connect this interface using RS-232 serial cable (not supplied) to

any Windows compatible PC to allow remote control of the M15 HD

via compatible external controllers.

• Refer to the NAD website for information about RS232 Protocol

documents and PC interface program.

6 +12V TRIGGER IN (OFF/AUTO)

• When at AUTO position, the M15 HD selects the +12V TRIGGER IN to

turn ON (if so assigned at the “Trigger Setup” menu) and at the same

time disables the HTRM and front panel’s ON/OFF function.

• When at OFF position, the trigger input is disabled.

WARNING

 If“AutoTriggerIn”atTriggerSetupmenuisassignedto“Main”or“All”

andthe+12VTRIGGERINswitchissetto“AUTO”mode,thestandby

buttoninthefrontpanelaswellasthecorrespondingON/OFFfunction

keysintheHTRMremotecontrolwillbedisabledeectivelyhandling

thisfunctiontoanexternalcontroller.Slideto“OFF”the+12VTRIGGER

INswitchtomaintainnormalpowerON/OFFfunctionprocedures.

7 IR IN/IR OUT 1-3

These mini-jacks accept and output remote-controlled codes in

electrical format, using industry-standard protocols, for use with “IR-

repeater” and multi-room systems and related technologies.

• All NAD products with IR IN/IR OUT features are fully compatible

with the M15 HD. For non-NAD models, please check with your

other product’s service specialists as to their compatibility to the

M15 HD’s IR features.

IR IN

• This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another compatible device

to allow control of the M15 HD from a remote location.

IR OUT 1, IR OUT 2

• Connect IR OUT 1 (and/or IR OUT 2) to the IR IN jack of a compatible

device.

• Command and control the linked compatible device by directing its

own remote control to M15 HD's infrared receiver.

IR IN and IR OUT 1, IR OUT 2, IR OUT 3

• Connect the M15 HD’s IR IN to the IR OUT of a compatible device.

Connect also the M15 HD’s IR OUT 1 (and/or IR OUT 2, IR OUT 3) to

the IR IN of a compatible device.

• With this setup, the M15 HD acts as an “IR-repeater” allowing the

device connected to the M15 HD’ s IR IN control or command of the

other device linked to M15 HD’s IR OUT 1 (and/or IR OUT 2, IR OUT 3).

IR OUT 3

• IR OUT 3 can only function as an “IR-repeater” as described above.

8 +12V TRIGGER OUT

The M15 HD has three +12V TRIGGER OUT ports (OUT 1, OUT2 and OUT3)

that can be congured to supply +12V DC to a linked component or

system. See discussion on “Trigger Setup” at the “Setup Menu” literature for

guidelines on how to congure +12V TRIGGER IN/OUT.

• Use a 3.5mm mini-jack connector to pass +12 volts at a maximum

current of 50 milliamps to an auxiliary equipment such as a

multichannel amplier or subwoofer. The center conductor (hot) of

the 3.5mm jack is the control signal. The outside conductor (shield)

is the ground return-path.

• This output will be 12V when the M15 HD is ON and 0V when the

unit is either OFF or in standby mode.

+12V TRIGGER IN

With this input triggered by a 12V DC supply, the M15 HD can be

switched ON remotely from standby mode by compatible devices such

as ampliers, preampliers, receivers, etc. If the 12V DC supply is cut o,

the M15 HD will return to standby mode.

• Connect this +12V Trigger input to the remote device’s

corresponding +12V DC output jack using a mono cable with

3.5mm male plug. The controlling device must be equipped with a

+12V trigger output to use this feature.

9 MP DOCK

The M15 HD is equipped with a data port in the rear panel where

an optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later

variants can be plugged in.

• Connect the “MP DOCK (DATA PORT)” jack of the M15 HD to the

corresponding “DATA PORT” socket of the optional NAD IPD model.

• AUDIO 4 IN and S-VIDEO 4 IN are the assigned default ports for the

audio/video output of the separately sold NAD IPD (NAD IPD Dock

for iPod) 1, NAD IPD 2 and later variants.

• Refer also to the “LISTENING TO YOUR iPod PLAYER” segment of the

“OPERATION” section.

NOTE

 TheNADIPDDockforiPodisnotsuppliedwithyourM15HD.

10 COMPONENT VIDEO IN 1-3, COMPONENT VIDEO MONITOR OUT

• Connect the Component Video Input to Component Video output

of compatible source components, typically a DVD player, BD

player, digital cable box or other applicable components. Connect

Component Video Monitor Out to the Component Video input of a

compatible video monitor/TV.

• Be sure to observe consistency in connecting the Y/Pb/Pr jacks

to the corresponding sources/inputs. The routing of the three

component video input is fully congurable via the Source Setup

item of the Setup Menu OSD.

• The M15 HD’s sets of component video input and output are fully

wideband and compatible with allowable HDTV formats.

11 MONITOR (S-VIDEO, VIDEO)

• Connect to the video input of a monitor/television using quality

dual-RCA and/or S-Video cables designed for video signals.

• In general, the S-Video connection is superior and should be used if

your TV/monitor provides the corresponding input.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

NAD M15 HD2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M15 HD2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info