Bedienungsanleitung NAD M32 DirectDigital DAC Amplifier (Seite 14 von 24) (Englisch)

667811

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

SUB MODE

• Set the subwoofer mode to either mono or stereo setting.

Mono: Select this setting when using one subwoofer. At mono mode,

the left and right channels are summed in the low pass subwoofer

output to drive a single subwoofer.

Stereo: Select this setting when using two subwoofers, one for the left

channel and one for the right channel.

MAIN FREQUENCY 40Hz to 200Hz and Full

MAIN TRIM 12.0dB to 0.0dB

• Crossover allows easy bi-amplication or subwoofer integration

by adding the required lters to redirect bass frequencies to the

subwoofer.

• Frequencies from 40Hz to 200Hz and Full can be selected, with the high

pass signal sent to the amplier section and the low pass signal sent to

Subwoofer Out.

SUB FREQUENCY 40Hz to 200Hz and Full

SUB TRIM 12.0dB to 0.0dB

• Selected subwoofer crossover frequency and below will be redirected

to subwoofer output.

• Sub trim provides exact volume matching of the subwoofer level to the

main speaker level.

NOTE

Since the low pass lter is already implemented in the M32, the

subwoofer should be set to the highest frequency crossover setting

available or bypassed if it also includes a crossover function.

SOURCE SETUP

Source Setup makes it possible to select a Source and enable or disable it

as desired. The optional DD AP-1 (Direct Digital Analog Phono), DD HDM-1

(HDMI) and MDC BluOS modules must be installed to select Sources like

Single-ended, Balanced, Digital HDMI 1 or BluOS. If the applicable module

is not installed, the corresponding sources will not be available from the

Source Setup menu selection.

--- : Non-MDC or built-in sources.

Slot A : Location slot of the Source module (MDC) in the rear panel.

Cable TV : Source name for Line 1 input. Source name can be changed in

the “Name” section shown below.

When a Slot line item is selected, the following menu options will be displayed.

Enabled: Source input can be enabled (ON) or disabled (OFF).

Name: Source input name. Selecting this line item will lead to the menu

keyboard where one can type the preferred name for the current source.

VOLUME CONTROL

The M32 VOLUME control function is dependent upon the “Volume

Control” menu setting. Volume control can either be set to “Fixed” or

“Variable”. Select “Save” to store selected “Volume Control” and “Fixed Level”

or “Variable” settings.

Fixed

If “Volume Control” is set to “Fixed”, audio output level is xed and the

M32’s volume control is bypassed. With “Fixed” volume control setting,

the M32 becomes like a basic amplier with volume controlled by an

external device.

• Set “Fixed Level” to desired preset dB level. Audio output is xed

to the selected level after saving the setting. Audio output level

will not change when using the Volume control or HTRM 2’s

[VOLR/T].

• At “Fixed Level” setting, the volume control or HTRM 2’s [VOL R/T]

will have no eect and eectively disabled.

Variable

• When set to “Variable”, audio output level is directly adjustable using

the volume control or HTRM 2’s [VOL R/T].

The following additional menu options are included if LINE 1 or LINE 2

input is selected.

OPERATION

USING THE M32

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M32 DirectDigital DAC Amplifier Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M32 DirectDigital DAC Amplifier

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info