Bedienungsanleitung NAD M32 DirectDigital DAC Amplifier (Seite 15 von 24) (Englisch)

667811

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Analog Gain: -12dB to 0dB. Gain adjustment allows all sources to play

back at the same volume level so you don’t need to adjust the volume

every time a new source is selected. It is generally preferable to reduce the

level of the loudest source rather than making louder the softer sources.

Sample Rate (48 kHz, 96 kHz, 192 kHz): Select the user’s preference

for sample rate of the Analog-to-Digital Converter. Higher sampling rates

allow for anti-aliasing lters to take eect further outside the audible

frequency range and are generally considered to sound better, especially in

the high frequencies. This option is applicable only for LINE 1 or LINE 2.

DIGITAL OUTPUT

SAMPLE RATE 48 kHz, 96 KHZ, 192 kHz

Audio inputs may come from various sources with dierent sampling rates.

Select 48 kHz, 96 kHz or 192 kHz to convert all digital audio output content

to single sampling rate.

CONTROL SETUP

AUTO STANDBY

Allows the option of the M32 going to standby mode after 15 minutes of

inactivity or remain at operating mode regardless of any source activities.

ON: M32 will automatically go to standby mode if there are no user

interface interaction and no active source within 15 minutes.

OFF: M32 remains at operating mode even if there is no user interface

interaction and no active source within 15 minutes. This is the default setting.

IR CHANNEL

The M32 has the capability to operate via Alternate IR channel. This is useful

if you have two NAD products that can be operated by similar remote

control commands. With alternate IR Channel, two dierent NAD products

can be controlled independently in the same zone by setting each one to a

dierent IR channel.

IR Channel Assignment

The M32 and the HTRM 2 remote control must be set to the same channel.

To change the IR Channel on the HTRM 2 remote control

• Include a channel number before the library code. For HTRM 2, library

code “100” is the default library table for “AMP” device. To select this

“AMP” library table for “IR Channel 0”, retain the library code “100”.

• If you want to load the “AMP” library table on “IR Channel 1”, prex the

library code with “1” to indicate association with “IR Channel 1”. Load

then the “AMP” library table using the code “1100”.

Sample setup of two NAD products on the same Zone

M32 and T 787 are both defaulted to IR Channel 0. If [OFF] button is pressed

on the HTRM 2 remote control (or HTR 8 remote control for the T 787), both

products will go to standby mode. Press [ON] and both products will power

up from standby mode.

To prevent both products from simultaneously going in and out of standby

mode along with other common commands, set each one to a dierent

IR channel. In this setup, we will keep T 787 and HTR 8 remote control

defaulted to “IR Channel 0”. As for M32, we will assign it to “IR Channel 1”;

the same applies to HTRM 2.

Set M32 and HTRM 2 to “IR Channel 1” via the following procedure.

M32

• Select “1” as the IR Channel setting of the M32.

HTRM 2

Ensure the M32 is powered-up (“on”, not merely in standby).

1 Press and hold together the [AMP] and [A/V PSET] buttons until the

Learn LED (located between HTRM 2’s ON and OFF buttons) turns

steady green. Release both buttons.

2 While keeping the HTRM 2 pointed towards M32, press “1”, “1”, “0” and “0”

using HTRM 2’s numeric buttons.

3 Press [OFF]. If the M32 goes to standby mode, this indicates that the

library input is successful.

4 Press [ENTER] to accept the library code input and exit the Library

mode.

With both M32 and HTRM 2 set to “IR Channel 1”, the M32 can now be

remotely controlled independent of the T 787.

NOTE

Performing a Factory Reset for HTRM 2 will result to a return to the

factory default “IR Channel 0” setting.

LISTENING TO COMPUTER

Use Type A to Type B cable connector to directly stream 24/192 PCM

content from your PC or MAC to the M32. Ensure that the Sound or Audio

device setting of your computer is set to “NAD USB Audio”.

MINIMUM PC SYSTEM REQUIREMENT

Microsoft Windows XP Service Pack 2 or higher, Microsoft Windows 7

FOR MAC USERS

Minimum Mac OS X Snow Leopard (version 10.6) and later versions

OPERATION

OTHER FEATURES

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M32 DirectDigital DAC Amplifier Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M32 DirectDigital DAC Amplifier

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info