Bedienungsanleitung NAD T 758 (Seite 15 von 42) (Englisch)

745046

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

ALTERNATE IR CHANNEL

The T 758 has the capability to operate via Alternate IR channel. This is

practically useful if you have two NAD products that can be operated by

similar remote control commands. With alternate IR Channel, two dierent

NAD products can be controlled independently in the same zone by

setting each one to a dierent IR channel.

IR CHANNEL ASSIGNMENT

The T 758 and the AVR 4 remote control must be set to the same channel.

To change the Main Zone IR Channel on the T 758

• Press and hold a SOURCE and then toggle STANDBY button to select

desired IR Channel – the VFD will show “IR Channel 1” or “IR Channel 0”.

The default IR Channel is “IR Channel 0”.

To change the IR Channel on the AVR 4 remote control

• Include a channel number before the library code. For AVR 4, library

code “10” is the default library table for “AMP” device. To select this “AMP”

library table for “IR Channel 0”, retain the library code “10” (or “010”).

• If you want to load the “AMP” library table on “IR Channel 1”, prex the

library code with “1” to indicate association with “IR Channel 1”. Load

then the “AMP” library table using the code “110”. Repeat the same for

MP (130) and TUNER (140).

SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE

NAD T 758 and NAD C 326BEE are both defaulted to IR Channel 0. If [OFF]

button is pressed on the AVR 4 remote control (or SR 8 remote control for

the C 326BEE), both products will go to standby mode. Press [ON] and both

products will power up from standby mode.

To prevent both products from simultaneously going in and out of standby

mode along with other common commands, set each one to a dierent

IR channel. In this setup, we will keep C 326BEE and SR 8 remote control

defaulted to “IR Channel 0”. As for T 758, we will assign it to “IR Channel 1”;

the same applies to AVR 4.

Set T 758 and AVR 4 to “IR Channel 1” via the following procedure.

T 758

• Press and hold a SOURCE and then toggle STANDBY button to

select “IR Channel 1”.

AVR 4

• Press and hold [AMP] in the DEVICE SELECTOR section of the AVR 4.

• While holding down the device button [AMP], press “1”, “1” and “0”

using AVR 4’s numeric buttons.

• Press [ENTER] while still holding down the device button [AMP]. The

AMP device selector will ash once to indicate that the library input

is successful.

With both T 758 and AVR 4 set to “IR Channel 1”, the C 326BEE can now be

remotely controlled independent of the T 758.

NOTE

Performing a Factory Reset for T 758 or AVR 4 will result to a return to the

factory default “IR Channel 0” setting.

IDENTIFICATION OF CONTROLS

AVR 4 REMOTE CONTROL

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 758 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 758

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info